Hornet 553T Скачать руководство пользователя страница 41

Страница: 41 / 60

Channels Five, Six and Seven:

Channels Five through Seven are used to assign the arm, disarm and panic func-

tions to separate buttons on the remote control. Teaching a button to Channel Five erases all information about

that remote from memory. Any auxiliary functions that are desired will have to be reprogrammed. Similarly, if the

remote is set up to use the separate arm, disarm and panic channels and a button from that remote is entered

into Channel One, the remote will be erased from memory, and the system will only recognize the button that

was entered into Channel One.

Channel Ten:

If any transmitter button from a known transmitter is programmed to Channel Ten, all transmitters

will be erased from memory and will revert to the default feature settings. (See

Features Menu

section of this

guide.) This is useful in cases when one of the customer's transmitters is lost or stolen. This will erase any lost

or stolen transmitters from the system's memory. It can also be used to start from scratch if the transmitter

buttons were programmed incorrectly.

Press the transmitter button.

While

HOLDING

the Valet®/Program switch, press the

button from the transmitter that you wish to assign to that channel. The unit will chirp

indicating successful programming. It is not possible to teach a transmitter button to the

system more than once.

Release.

Once the code is learned, the Valet®/Program button can be released.

You can advance from one channel to another by releasing the Valet® /Program button and tapping it to advance

channels and then

HOLDING

it. For example, if you want to program Channel Three after programming Channel

One, release the Valet®/Program button. Press it twice and release it to advance to Channel Three. Then press it

once more and

HOLD

it. The siren will chirp three times to confirm it is ready to receive the code from the trans-

mitter.

Learn Routine™ will be exited if:

■

Ignition is turned off.

■

Door is closed.

■

Valet®/Program button is pressed too many times.

■

More than 15 seconds elapses between steps.

One long chirp indicates that Learn Routine™ has been exited.

Содержание 553T





























































Результаты поиска

Содержание 553T

Отзывы:

Бренды по названию

Популярные бренды

Hornet 553T, Руководство по установке

Результаты поиска

Содержание 553T

Отзывы:

Бренды по названию

Популярные бренды