Hornet 553T Скачать руководство пользователя страница 30

Страница: 30 / 60

ceiver will excite the transponder, which is located (but not visible) in the head of the ignition key. The key

transponder will then send a unique code back to the transceiver for evaluation. If the code matches a valid code

of the system, the vehicle will be allowed to start. Most of these transponder-based systems can be bypassed

using

p/n 555U.

Some may require additional parts from the vehicle manufacturer. Consult you dealer for the

applications. For most Ford PATS transponders,

p/n 555F

can be used, except for the following vehicles, which

will require

p/n 555U

: ‘97 and newer Mark VII, and 2000 and newer Taurus/Sable, Contour/Mystique and Focus.

plug-in LED and valet/program switch

These plug into the module. The Status LED plugs into the small two-pin socket, while the Valet® /Program

Switch should be plugged into the larger blue two-pin connector. The Status LED fits into a

-inch hole.

Status LED

Valet®/Program Switch

programmer interface, 3-pin black plug

The black 3-pin port is provided for personal computer programming of the unit. The unit can also be pro-

grammed using the Bitwriter (

p/n 998T

). When using the optional PC Interface module, or hand-held

programmer, it is possible to configure any and all of the programmable functions as well as lock the

Transmitter/Receiver and System Features Learn Routines so that unauthorized users cannot change the config-

uration or program transmitters to the unit.

When the learn routines have previously been programmed using an optional hand-held system programmer

(

p/n 998T

) or PC Interface module, they may have been locked. Before proceeding with reprogramming

the learn routines, they must be unlocked with either the 998T or the PC Interface module - this cannot be done

manually with the Valet switch.

Содержание 553T





























































Результаты поиска

Содержание 553T

Отзывы:

Похожие инструкции для 553T

Бренды по названию

Популярные бренды

Hornet 553T, Руководство по установке

Результаты поиска

Содержание 553T

Отзывы:

Похожие инструкции для 553T

Бренды по названию

Популярные бренды