manualshive.com logo in svg

Hornet 553T, Руководство по установке

Поделиться
Скачать
Hornet 553T Скачать руководство пользователя страница 32

32

© 2000 Directed Electronics, Inc. Vista, CA

tach learning

To learn the tach signal:

1.

Start the vehicle with the key.

2.

Within 5 seconds, press and 

HOLD

the Valet®/Program switch.

3.

The LED will light constant when the tach signal is learned.

4.

Release the Valet®/Program switch.

door lock harness (H4) wire connection guide

______

______

______

This system can control two common power door lock types without any additional parts! With certain vehicles,

or if an actuator is to be installed, either a 

451M

Door Lock Relay Satellite or two relays will be required.

IMPORTANT!

If you mistake a Type C direct-wired system for a Type A positive-pulse system, the

module will be damaged! 

This system can control two common power door lock types without any additional parts! With certain vehicles,

or if an actuator is to be installed, either a 

451M

Door Lock Relay Satellite or two relays will be required.

BLUE

(-) UNLOCK, (+) LOCK OUTPUT

EMPTY

UNLESS USING 451M

GREEN

(-) LOCK, (+) UNLOCK OUTPUT

H4/A

H4/B

H4/C

DRW-96

Содержание 553T





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды