Hornet 553T Скачать руководство пользователя страница 56

Страница: 56 / 60

troubleshooting

■

Shock sensor doesn't trigger the alarm:

Has the NPC™ system been triggered? If so, you will hear 5 chirps when disarming. To check this, turn the igni-

tion key on and off to clear the NPC™'s memory, and then retest the shock sensor. For a detailed description of

NPC™, see

Nuisance Prevention Circuitry

section of this guide.

■

Door input does not immediately trigger full alarm. Instead, chirps are heard for the first 3 seconds:

That's how the progressive two-stage door input works! This is a feature of this system. This is an instant trigger,

remember, since even if the door is instantly closed again, the progression from chirps to constant siren will continue.

■

Closing the door triggers the system, but opening the door does not:

Have you correctly identified the type of door switch system? This happens often when the wrong door input has

been used. (See

Door Lock Harness Wire Connection Guide

section of this guide.)

■

System will not passively arm until it is remotely armed and then disarmed:

Are the door inputs connected? Is the H1/6 blue wire connected to the door trigger wire in the vehicle? Either

the H1/5 green or the H1/7 violet should be used instead. (See wiring diagrams.)

■

Door input does not respond with the progressive trigger, but with immediate full alarm:

Does the Status LED indicate that the trigger was caused by the shock sensor? (See

Diagnostics

section of this

guide.) The shock sensor, if set to extreme sensitivity, may be detecting the door unlatching before the door

switch sends its signal. Reducing the sensitivity can solve this problem.

■

The Valet®/Program switch doesn't work.

Is it plugged into the correct socket? See

Plug-In LED and Valet®/Program Switch

section of this guide.

■

Status LED doesn't work.

You've probably guessed already, but here goes: Is it plugged in? (See

Plug-In LED and Valet®/Program Switch

section of this guide.) Is the LED plugged into the correct socket?

■

Door locks operate backwards.

This unit has easily-reversed lock/unlock outputs. Recheck wire connections to see if you have reversed these.

■

The remote start will not activate.

1. Check the harnesses and their connections. Make sure that the harnesses are completely plugged into the

remote start module. Make sure there are good connections to the vehicle wiring.

remote start troubleshooting

alarm troubleshooting

Содержание 553T





























































Результаты поиска

Содержание 553T

Отзывы:

Похожие инструкции для 553T

Бренды по названию

Популярные бренды

Hornet 553T, Руководство по установке

Результаты поиска

Содержание 553T

Отзывы:

Похожие инструкции для 553T

Бренды по названию

Популярные бренды