horiba LAQUA-PC1500 Скачать руководство пользователя страница 39

Страница: 39 / 100

Temperature Calibration

● Temperature Calibration

Temperature calibration is required to accurately match pH and conductivity electrode to the

meter. Check the temperature reading and if it is acceptable, no temperature calibration is

required. If you need to calibrate, please follow the procedure detailed below:

Prerequisites

• Clean the pH or conductivity electrode with DI (deionized) water and wipe it with tissue

paper.

• Switch on the meter and plug in the electrode and temperature sensor.

• Dip the electrode in any buffer solution until its temperature sensor is immersed.

• Wait for 5 minutes to ensure temperature stability.

• Meter displays

MTC

if the temperature sensor is not plugged in and displays

ATC

if the

temperature sensor is plugged in.

• Temperature calibration must be performed using a known temperature solution or against

a calibrated thermometer.

To abort an ongoing calibration process at any point of time, press the

key.

Note

Tip

Содержание LAQUA-PC1500





































































































Результаты поиска

Содержание LAQUA-PC1500

Отзывы:

Бренды по названию

Популярные бренды

horiba LAQUA-PC1500, Инструкция по эксплуатации

Результаты поиска

Содержание LAQUA-PC1500

Отзывы:

Бренды по названию

Популярные бренды