manualshive.com logo in svg

Honeywell SmartValve SV9520H, Руководство пользователя, Страница: 12 / 16

Поделиться
Скачать
Honeywell SmartValve SV9520H Скачать руководство пользователя страница 12

SV9520H SMARTVALVE™ SYSTEM CONTROL LINE VOLTAGE POLARITY SENSE MODELS

69-1383

12

Fig. 11. SV9520 sequence of operation.

APPLY POWER TO APPLIANCE

THERMOSTAT CALLS FOR HEAT

AIR PROVING SWITCH PROVED 
OPEN? 

COMBUSTION AIR BLOWER ON

HOT SURFACE IGNITER ON 
FOR WARM-UP TIME

CIRCULATING AIR FAN ON 
AFTER DELAY

MAIN BURNER LIGHTS AND IS 
SENSED DURING TRIAL
 FOR IGNITION?

 MAIN VALVE OPENS

HOT SURFACE IGNITER OFF

FLAME SENSE LOST?

THERMOSTAT CALL FOR 
HEAT ENDS

FIVE-MINUTE WAIT PERIOD

WAIT FOR AIR PROVING
SWITCH TO OPEN    

FLAME SENSE LOST MORE 
THAN FIVE TIMES IN THIS CALL
 FOR HEAT OR OTHER 
ABNORMAL OPERATION?

PREPURGE

30 SECONDS
BETWEEN TRIAL PURGE

AIR PROVING SWITCH PROVED 
CLOSED WITHIN 30 SECONDS?

COMBUSTION AIR BLOWER OFF

MAIN VALVE CLOSES

COMBUSTION AIR BLOWER 
OFF AFTER POST PURGE

1 HOUR AUTO LOCKOUT
 RESET DELAY

MAIN VALVE CLOSES

COMBUSTION AIR BLOWER OFF 
AFTER POST PURGE

CIRCULATING AIR FAN OFF
AFTER DELAY

WAIT FOR NEXT CALL FOR HEAT

FAILED TRIALS FOR IGNITION 
LESS THAN FOUR DURING
THIS IGNITION SEQUENCE?

NO

NO

YES

YES

YES

NO

NO

MAIN VALVE CLOSES

YES

YES

NO

YES

NO

M17610

SV9520 DIRECT HOT SURFACE IGNITION SmartValve™ SYSTEM CONTROL 

SEQUENCE OF OPERATION WITH ST9160 ELECTRONIC FAN TIMER OR 208907 TERMINAL BOARD 

2

3

1

CIRCULATING AIR FAN OFF
AFTER DELAY

2

1

2

3

WHEN SmartValve™ IS POWERED, LED WILL BE IN 
"HEARTBEAT" MODE (BRIGHT-DIM-BRIGHT-DIM, ETC.).

THIS FUNCTION OCCURS ONLY WITH ST9160 
CONNECTED TO SmartValve™ SYSTEM CONTROL.

SEE TROUBLESHOOTING SECTION FOR DETAILED INFORMATION.

1

Содержание SmartValve SV9520H

















Отзывы:

Нет отзывов