Honeywell GSMVLP4G Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 24

Honeywell GSMVLP4G Скачать руководство пользователя страница 4

– 4 –

GSMVLP4G Module Kit

This kit contains the following components:

Figure 1 – GSMVLP4G Kit Components

Installing the GSMVLP4G module

1. Disconnect power from the control, including the battery, BEFORE installing the GSMVLP4G

module.

2. CAUTION: ESD SENSITIVE DEVICE. To discharge any static buildup, briefly touch a chassis

ground point before installing this module. Avoid performing this installation while standing
on a carpeted floor

.

Opening the Lynx Plus or ReadyGuard Plus Series Control and Installing GSMVLP4G

1. Install the appropriate FCC/IC label (provided) on the control’s back case as shown on Figure 2.

Figure 2 – FCC/IC Label location

RF Exposure

WARNING: The antenna(s) used for this transmitter must be installed to provide a separation

distance of at least 7.8 in (20 cm) from all persons and must not be co-located or operating in

conjunction with any other transmitter except in accordance with FCC multi-transmitter product

procedures.

Mise en Garde

Exposition aux Fréquences Radio: L'antenne (s) utilisée pour cet émetteur doit être installée à une

distance de séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes.

FCC LABEL NOTE:

Affix the appropriate FCC

“Contains Transmitter Module”

label over the top portion of the

control’s FCC label. Use the label

that matches the LYNX FCC ID

found on the Control’s label.

«
...
2
3
4
5
6
...
»

Содержание GSMVLP4G

























Отзывы:

Нет отзывов