Honeywell Gent Compact Plus Скачать руководство пользователя страница 80

Страница: 80 / 133

S-Quad & S3 Mk2/Mk3

Sector

setup

For any Sounder to make a sound,

Audible On

must be ticked against that

Signal.
If Speech is to be used, Speech
Operation must be ticked against that
Signal.
VAD/Str Actioned if ticked will flash any
VADs or Strobes for that Signal.

Note: A Combined Sounder/VAD must
have at least one output working.

For Standard Panel Signals (No Voice Messages) set

Low/Attn Tone

AND

High/Message

00.

Also Ensure that

Speech Operation

is unticked.

To use Voice Messages (Voice Enabled Devices) set

Low/Attn Tone

and set the

High/Message

to the required Message. Ensure that

Speech

Operation

is ticked.

Codes:

= standard tone for signal

= message 1 (bell ring)

= voice message 2 to 5

Note: If no Sounder/Voice Devices are in this Sector the Low/Attn Tone
and High Message will have the value of FF

Strobe period:

(2 seconds

between Flashes)

Pre speech & post speech:

Gap between attention tone
and message

Sndr - Sector can be setup

E.g. Sector 1 Loop 2;

on receipt of a sig 2 instruction, all ‘sounders’ will provide standard ‘evac’ attention tone

followed by message 5 in a loop and VAD/Strobes will flash with a 2 sec on/off rate

Warning

– Do not use Voice Messages if you have a mix of Voice and

Non-Voice enabled devices in the same sector.

Содержание Gent Compact Plus






































































































































Результаты поиска

Содержание Gent Compact Plus

Отзывы:

Похожие инструкции для Gent Compact Plus

Бренды по названию

Популярные бренды

Honeywell Gent Compact Plus, Руководство пользователя

Результаты поиска

Содержание Gent Compact Plus

Отзывы:

Похожие инструкции для Gent Compact Plus

Бренды по названию

Популярные бренды