Honeywell Gent Compact Plus Скачать руководство пользователя страница 52

Страница: 52 / 133

Commissioning Tool - Downloading and Installing

•

Log into

www.gentexpert.co.uk

and select the

Download

Tab.

•

Select the

Software, Commissioning Tools and Drivers

section

•

Select the

Vigilon Commissioning Tool

section and the select the

Vigilon Commissioning Tool.

•

Click on the Download button and If prompted, Select

Save As

and browse to a desired save location.

•

Browse to the location where the .zip file was saved and Extract the file.

•

Determine whether your PC’s Operating System is 32 bit or 64 bit.

•

Browse to the extracted Commissioning Tool Folder then select the folder applicable to your

Operating System.

•

Run the setup program to install the Commissioning Tool

– Accept the default locations.

•

Do not start the Commissioning Tool yet.

Commissioning Tool

– Install the Crypkey Service

Commissioning Tool - Downloading and Installing

•

Browse to the following folder on your PC

32 bit Operating Systems

–

C:\Program Files\Honeywell\Commissioning Tool

64 bit Operating Systems

–

C:\Program Files (x86)\Honeywell\Commissioning Tool

•

Locate and run the setupex.exe program

•

After a short interval the following message will appear:-

•

Click the OK button and then Start the Commissioning Tool from the Desktop Icon

•

You will now be able to Licence your Commissioning Tool.

Содержание Gent Compact Plus






































































































































Результаты поиска

Содержание Gent Compact Plus

Отзывы:

Похожие инструкции для Gent Compact Plus

Бренды по названию

Популярные бренды

Honeywell Gent Compact Plus, Руководство пользователя

Результаты поиска

Содержание Gent Compact Plus

Отзывы:

Похожие инструкции для Gent Compact Plus

Бренды по названию

Популярные бренды