Honeywell Gent Compact Plus Скачать руководство пользователя страница 56

Страница: 56 / 133

Node 1 Domain 1
Port 0:  1200   Off
Port 1:  38400 None
Port 2:  38400 None
Port 3:  38400 None

Connecting the Commissioning Tool to the Panel

Before we can use the Commissioning Tool to communicate
with the Fire Panel we need some details about the panel.

INFO > STATUS > CARD {0} > ENTER

Card 0:

Fault 0 Disable 0 Warning 0

Controller (2) Version 4.37 21/11/06

Node Address

On power up, a new EN Panel
(Without a Network card
Fitted) the node address will
not be set up.
To Change or Setup the Node
Address:

TestEng > Usercode >Config
> Comms > Address
{type in required node
address in the range of 1 to
32} > Enter

Domain Number

On an EN Panel by default
this will be set at

Domain 1.

To Change the Domain
Number if required:

TestEng > Usercode >
Config > Comms > Domain
{type in required Domain
address in the range of 1 to
255} > Enter

Version

3.xx = BS
4.xx = EN

RS232 Ports

Compact Only

Communication Port and Baud Rate:-

Ports 1 & 2 (Compact Panel only) are the serial (RS232) Ports and

Port 3 is the USB port. To change the baud rate use:-

TestEng > Usercode > Config > Comms > Card {0} Enter > {Type the Port No} > Enter > Baud > Enter
> {Use the Previous and Next options to adjust the Baud rate} > Enter

Содержание Gent Compact Plus






































































































































Результаты поиска

Содержание Gent Compact Plus

Отзывы:

Похожие инструкции для Gent Compact Plus

Бренды по названию

Популярные бренды

Honeywell Gent Compact Plus, Руководство пользователя

Результаты поиска

Содержание Gent Compact Plus

Отзывы:

Похожие инструкции для Gent Compact Plus

Бренды по названию

Популярные бренды