Honeywell ControLinks R7999A Скачать руководство пользователя страница 14

Страница: 14 / 16

R7999A,B CONTROLINKS™ CONTROLLER

65-0238—10

Go back into the Commission mode of the ZM software

or S7999 Touchscreen display and enter your password,

but DO NOT press enter.

Go to the R7999 ControLinks and press the Reset but-

ton. As it turns on the different LEDs, press the “Enter”

command on the Commission screen to enter the pass-

word. You should be into the setup screen. If the R7999

Alarms again, you may need to repeat the above steps.

You cannot enter ControLinks commissioning while it is

in Alarm.

Once you have entered the Commission screen, return

to the replaced actuator and reconnect the Red connec-

tor.

Return to the commissioning process by entering the

new actuator and setting up the end points.

Reload the profile curve and verify the curve.

Содержание ControLinks R7999A

















Результаты поиска

Содержание ControLinks R7999A

Отзывы:

Похожие инструкции для ControLinks R7999A

Бренды по названию

Популярные бренды

Honeywell ControLinks R7999A, Руководство пользователя

Результаты поиска

Содержание ControLinks R7999A

Отзывы:

Похожие инструкции для ControLinks R7999A

Бренды по названию

Популярные бренды