Honeywell CENTRA LINE EAGLEHAWK Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 32

background image

EAGLEHAWK CONTROLLER – INSTALLATION & COMMISSIONING INSTRUCTIONS

29

EN1Z-1005GE51

R0216

Tx and Rx LEDs

Table 25. EAGLEHAWK controller bus LEDs Tx and Rx

case bus LEDs

meaning

remedy

1

Both Tx and Rx

are flashing

Normal operation; RS485-1 is functioning
properly.

No action necessary

2

Both Tx and Rx

are OFF

No communication on RS485-1.

►

Switch ON communication on RS485-1. L1 should
then flash. Further handling like case 4 (below).

3

Rx is flashing

and Tx is OFF

Communication on RS485-1 has been
switched OFF, but the EAGLEHAWK is
receiving data from other controllers.

►

Switch ON communication on RS485-1. If this
proves unsuccessful, the hardware may be
defective.

4

Tx is flashing

and Rx is OFF

The EAGLEHAWK controller is attempting to
establish communication on RS485-1, but
there is no answer.

►

The communication rate (Kbaud) on RS485-1 has
not been correctly set; other controllers on the bus
may have been incorrectly assigned the same
device number; wiring problem or hardware defect.

Panel Bus I/O Module Troubleshooting

Please refer to CentraLine I/O Modules - Installation & Commissioning Instructions (EN1Z-0973GE51) for more information
about Panel Bus I/O module troubleshooting.

«
...
27
28
29
30
31
...
»

Содержание CENTRA LINE EAGLEHAWK

































Отзывы:

Нет отзывов

Похожие инструкции для CENTRA LINE EAGLEHAWK

Бренд: Tapeswitch Страницы: 13

Бренд: Baby Jogger Страницы: 24

Бренд: Baby Jogger Страницы: 16

city select LUX

Бренд: Baby Jogger Страницы: 20

CITY ELITE SINGLE

Бренд: Baby Jogger Страницы: 24

Бренд: Baby Jogger Страницы: 147

Бренд: Icom Страницы: 30

Бренд: ICM Controls Страницы: 2

Бренд: ICM Controls Страницы: 2

Бренд: ray Страницы: 11

Бренд: jablotron Страницы: 2

Бренд: Laird Страницы: 38

Бренд: Laird Страницы: 5

Бренд: Parker Страницы: 16

Бренд: ZKTeco Страницы: 2

Extra Free RZB-02

Бренд: Zamel Страницы: 2

Бренд: Yamaha Страницы: 2

Бренд: Daikin Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды