Honeywell CENTRA LINE EAGLEHAWK Скачать руководство пользователя страница 28

Страница: 28 / 32

EAGLEHAWK CONTROLLER – INSTALLATION & COMMISSIONING INSTRUCTIONS

EN1Z-1005GE51 R0216

TROUBLESHOOTING

EAGLEHAWK Controller Troubleshooting

The following LEDs of the EAGLEHAWK controller can be used for troubleshooting purposes:



Power

LED

(green)



Status LED (red)



L1 and L2 LEDs (yellow)



Tx (sending data on RS485-1) and Rx (receiving data on RS485-1) LEDs

Power LED (green) of EAGLEHAWK

Table 21. EAGLEHAWK controller power LED

case power LED

meaning

remedy

Normal operation

No action necessary.

OFF

Power supply not OK.

►

Check power supply voltage.

►

Check wiring.

►

If problem persists, replace hardware.

Status LED (red) of EAGLEHAWK

Table 22. EAGLEHAWK controller status LED

case status LED

meaning

remedy

OFF after
power-up

Normal operation.

No action necessary.

ON con-
tinuously after
power-up

– No or invalid firmware, or
– No or corrupt application.

►

Try powering down and then powering up the
EAGLEHAWK controller.

►

If problem persists, replace hardware.

L1 LED

Table 23. EAGLEHAWK controller bus L1 LED

case bus LEDs

meaning

remedy

ON con-

tinuously after

power-up

Normal operation; this may continue for
several minutes until the platform is running

No action necessary.

Flashes

constantly

The platform is running

No action necessary.

Dark

Severe software problems.

►

Contact TAC.

L2 LED

Table 24. EAGLEHAWK controller bus L2 LED

case bus LEDs

meaning

remedy

ON con-

tinuously after

power-up

Station is starting up. It may take several
minutes until the station is ready to
communicate.

No action necessary.

►

If you are unable to establish communication,
consult "Application Director Output" in COACH

Dark

Station is not running

►

Contact TAC.

Содержание CENTRA LINE EAGLEHAWK

































Результаты поиска

Содержание CENTRA LINE EAGLEHAWK

Отзывы:

Похожие инструкции для CENTRA LINE EAGLEHAWK

Бренды по названию

Популярные бренды

Honeywell CENTRA LINE EAGLEHAWK, Инструкции по установке и пусконаладке

Результаты поиска

Содержание CENTRA LINE EAGLEHAWK

Отзывы:

Похожие инструкции для CENTRA LINE EAGLEHAWK

Бренды по названию

Популярные бренды