Honeywell CENTRA LINE EAGLEHAWK Скачать руководство пользователя страница 20

Страница: 20 / 32

EAGLEHAWK CONTROLLER – INSTALLATION & COMMISSIONING INSTRUCTIONS

EN1Z-1005GE51 R0216

BACNET MS/TP BUS CONNECTION

The EAGLEHAWK controller features two RS485 interfaces to which BACnet MS/TP devices can be connected: RS485-1
(consisting of push-in terminals 24 [GND-1], 25, and 26) and/or RS485-2 (consisting of push-in terminals 29, 30, and 31 [GND-
2]).

NOTE:

GND-2 is internally connected with 24V-0 (terminal 1)

BACnet MS/TP Bus Considerations



RS485-1 (isolated)

Max. BACnet MS/TP bus length: 800-1200 meters, depending on baud rate (see section “RS485 Standard” on pg. 8).

Use only shielded, twisted-pair cable and daisy-chain topology.

Must conform to EIA-RS485 cabling guidelines (see section "EIA 485 Cable Specifications" on pg. 18).



RS485-2 (non-isolated)

Max. BACnet MS/TP bus length: 800-1200 meters, depending on baud rate (see section "RS485 Standard" on pg. 8).

Use only shielded, twisted-pair cable and daisy-chain topology.

Ground noise should not exceed the EIA-485 common mode voltage limit.

Must conform to EIA-RS485 cabling guidelines.

Should not extend beyond a single building.

Connecting EAGLEHAWK via its RS485-1 Interface to a BACnet MS/TP Bus

With regards to Fig. 32 through Fig. 34, please note the following:

NOTE:

Always power each EAGLEHAWK controller and the connected BACnet MS/TP modules via separate transformers.

NOTE:

For “L,” see section “RS485 Standard” on pg. 8.

NOTE:

If any devices are not electrically isolated, signal ground connection is recommended. See section “RS485 Standard”
on pg. 8).

Example 1: Single EAGLEHAWK Controller and Connected BACnet Modules (with inserted termination

resistor)

1 2

242526

230 V

24 V

GND-1

+5V

ISO

RS485-1 (+) RS485-1 (-)

550 kOHM

150 kOHM

550 kOHM

END

MID

BACnet

Module #1

BACnet

Module #2

5 +

5 -

BACnet

Module #3

BACnet

Module #4

BACnet

Module #N-1

BACnet

Module #N

5 +

5 -

5 +

5 -

*CONNECT GND, IF AVAILABLE.

120 OHM

EAGLEHAWK

Fig. 32. Connection of a single EAGLEHAWK controller via its RS485-1 interface to a BACnet MS/TP Bus

The termination resistor must be inserted directly into the terminals of the last BACnet MS/TP module.

Содержание CENTRA LINE EAGLEHAWK

































Результаты поиска

Содержание CENTRA LINE EAGLEHAWK

Отзывы:

Похожие инструкции для CENTRA LINE EAGLEHAWK

Бренды по названию

Популярные бренды

Honeywell CENTRA LINE EAGLEHAWK, Инструкции по установке и пусконаладке

Результаты поиска

Содержание CENTRA LINE EAGLEHAWK

Отзывы:

Похожие инструкции для CENTRA LINE EAGLEHAWK

Бренды по названию

Популярные бренды