Honeywell AlarmNet 7847i-E Скачать руководство пользователя страница 41

Страница: 41 / 64

Section 5: Programmer Keyboard Commands

5-3

[X]

Reset CPU Y/N

Reset the 7847i/7847i-E

Pressing [N] returns to diagnostic mode (blank screen =
enter next command or escape).
Pressing [Y] resets the module (blank screen = reset
complete).

[

↑↑↑↑

]

(UP arrow)

Registering …

Registration

Registers a programmed 7847i-E

with the 7810iR-ent if

it is configured to report on the Private LAN. If it is
configured to report to AlarmNet, the 7847i/7847i-E

will

Section 4:

Registration

[

↓↓↓↓

]

(DN arrow)

Enter PIN#

Registration with PIN for Replacement Module

Registers a replacement unit with AlarmNet, once
programmed, using the existing PIN #.

If Private LAN is enabled, down arrow is not applicable.

[0]

Force Server Update?
Y/N_

Force Upload of Configuration File to Server

Pressing [Y] will force the device to upload its entire
configuration file to the server.

Pressing [N] cancels the operation.

NOTE:

If Private LAN is enabled, "Function

Unavailable" is displayed.

[ENTER]

Strt Prog Mode?
Y/N_

Enter Program Mode

Press [Y] to enter program mode; otherwise, press [N].

Содержание AlarmNet 7847i-E

































































Результаты поиска

Содержание AlarmNet 7847i-E

Отзывы:

Бренды по названию

Популярные бренды

Honeywell AlarmNet 7847i-E, Инструкция по установке и настройке

Результаты поиска

Содержание AlarmNet 7847i-E

Отзывы:

Бренды по названию

Популярные бренды