Honeywell AlarmNet 7847i-E, Инструкция по установке и настройке

Страница: 33 / 64

Section 3: Programming the 7847i/7847i-E
3-19
PROMPTS
ZONE
TRIG.
4204/
2-4204
ENTRY OPTIONS DESCRIPTION
63
Restore Zn6 Y/N
(Y)_
✔ ✔
[Y], [N] Enables restore reporting for zone 6.
64
Delay Zn6 (secs)
(00)_
✔ ✔ [01-15]
[00] = no delay
Defines the reporting delay in seconds for zone 6.
65
Rpt Zn6 ONLY if
Armed (N)_
✔ ✔
[Y], [N] Reports alarms on zone 6 ONLY if the
conditional zone (zone 7 in zone trigger mode;
zone 4 in 4204 mode; zone 8 in 2-4204 mode) is
triggered (armed).
If [N], always reports alarms on zone 6.
66
Enable Zn7 Y/N
(N)_
4204
only
[Y], [N] Enables alarm reporting for zone 7.
If [N], skip to Prompt 73: "Use DHCP."
67
Zn7 Trigger Type
(V+)_
✔
4204
only
•
(EOLR)
•
(V+)
•
(V–)
Selects the triggering method for this zone input.
Press the [space] key to scroll through choices.
68
Invert Zn7 Y/N
(N)_
✔
4204
only
[Y], [N] Inverts the alarm and normal states of the zone
7 trigger; otherwise uses normal input signal.
69
Restore Zn7 Y/N
(Y)_
✔ ✔
[Y], [N]
Enables restore reporting for zone 7.
Zone Trigger mode: This question will only be
displayed if zone 7 is not used as the conditional
(arming) trigger zone.
70
Delay Zn7 (secs)
(00)_
✔ ✔ [01-15]
[00] = no delay
Defines the reporting delay in seconds for zone 7.
Zone Trigger mode: This question will only be
displayed if zone 7 is not used as the conditional
(arming) trigger zone.
71
Rpt Zn7 ONLY if
Armed (N)_
✔ [Y], [N]
Reports alarms on zone 7 ONLY if the
conditional zone (zone 4 in 4204 mode; zone 8 in
2-4204 mode) is triggered (armed).
If [N], always reports alarms on zone 7.
2-4204 mode: If any zone is programmed to
"Report Only if Armed," or if tamper is enabled,
skip to Prompt 73: "Use DHCP."
72
Delay Zn8 (secs)
(00)_
2-
4204
only
[01-15]
[00] = no delay
Defines the reporting delay in seconds for zone 8.
73
Use DHCP Y/N
(Y)_
✔ ✔
[Y], [N]
Dynamically allocates the IP addresses
(recommended).
If Private LAN is enabled, skip to Prompt 79:
"Review." Otherwise, skip to Prompt 78: "Enable
Pwr Save."
If [N], uses fixed IP addresses.
74
NIC IP Address:
255.255.255.255_
✔ ✔
12 digit:
xxx.xxx.xxx.xxx
Enter the 4-part address for this device. The four
parts of the address must be separated by spaces
(displayed as periods in Review mode).
75
Subnet Mask:
255.255.255.255_
✔ ✔ 12 digit:
xxx.xxx.xxx.xxx
Enter the 32-bit address mask used to indicate
the portion (bits) of the IP address that is being
used for the subnet address. The four parts of
the address must be separated by spaces
(displayed as periods in Review mode).
76
Gateway IP Addr:
255.255.255.255_
✔ ✔
12 digit:
xxx.xxx.xxx.xxx
[0.0.0.0.] = not
used
Enter the 4-part address assigned to the
Gateway. The four parts of the address must be
separated by spaces (displayed as periods in
Review mode).