manualshive.com logo in svg

Honeywell AlarmNet 7847i-E, Инструкция по установке и настройке

Поделиться
Скачать
Honeywell AlarmNet 7847i-E Скачать руководство пользователя страница 16

7847i/7847i-E Installation and Setup Guide 

3-2

 

Each key of the 7720P has two possible functions: a normal function and a Shift function.  

To perform a normal key function, simply press the desired key. To perform a Shift function, 
press the [shift] key, and then press the appropriate key.  

The prompts in this document reflect use of the 7720P Programming Tool. Table 2 below lists 
each normal and shift key function. 

Table 2. 7720P Normal and Shift Key (shift LED lit) Functions 

KEY 

NORMAL KEY FUNCTION 

SHIFT KEY FUNCTION 

BS/ESC 

[BS]: Press to delete entry 

[ESC]: Press to quit program mode; also can reset 
programming defaults* 

↓

/

↑

 

[

↓

]: Scroll down programming 

[

↑

]: Scroll up programming 

N/Y 

[N]: Press for "NO" answer 

[Y]: Press SHIFT-Y for "YES" answer 

SHIFT 

Press before pressing a SHIFT key function. Will light SHIFT LED. LED goes out once a key 
is pressed. Press again for each SHIFT function desired. 

1/A 

[1]: For entering the number 1 

[A]: For entering letter A 

2/B 

[2]: For entering the number 2 

[B]: For entering letter B 

3/C 

[3]: For entering the number 3 

[C]: For entering letter C 

4/D 

[4]: For entering the number 4 

[D]: For entering letter D 

5/E 

[5]: For entering the number 5 

[E]: For entering letter E 

6/F 

[6]: For entering the number 6 

[F]: For entering letter F 

7/S 

[7]: For entering the number 7 

[S]: For entering letter S 

8/T 

[8]: For entering the number 8 

[T]: For entering letter T 

9/X 

[9]: For entering the number 9 

[X]: For entering letter X 

SPACE 

[SPACE]: For scrolling option list 

No SHIFT function 

0 

[0]: For entering the number 0 

No SHIFT function 

#/ENTER 

[#/ENTER]: Press to accept entries 

No SHIFT function 

* Active only when the "Exit Programming Mode" prompt is displayed. 

Using the Control Panel Programming Mode 

Some control panels support programming of the 7847i/7847i-E through the control 
panel programming mode (e.g., Vista-128BP). If programming through the control 
panel, only the ECP Mode programming options are available. The "mode" questions 
will not be displayed, and the mode cannot be changed. For a description of key 
functions on the control panel keypad, and how they map to the 7720P Programming 
tool, refer to the control panel's Programming Guide. 

Programming Conventions 

Programming is accomplished by answering a series of prompts (questions).  Most prompts 
require only a [Y]es or [N]o response, while others require a numerical response (ID 
numbers, etc.).   

The current value is displayed on the second line in parentheses ( ).  A "?" indicates an 
invalid entry.   

Use the [ENTER] key to accept the current entry and proceed to the next prompt.  If the 
current value is invalid, pressing [ENTER] re-displays the prompt; the next prompt is not 
displayed until a valid answer is entered.   

Use the up/down arrow keys to scroll through the programming questions without changing 
any values.  Press the [ESC] key to go to the end of the list of questions. 

ECP Mode Programming 

Press the [ENTER] key to begin programming. 

 

NOTE:

 

The central station can remotely block access to local 

device programming. If this has been done, the 
following prompt appears: 

 

Access to Prog 
Mode Denied

 

 

Содержание AlarmNet 7847i-E

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды