Honda HSM1380i Скачать руководство пользователя | Manualshive

Страница: 75 / 130

background image

73

– 6. Run the snow thrower at an adequate speed by operating the

main shift lever.

– 7. After running, turn the engine switch to the OFF position.

NOTE:

• Use the battery run mode to drive the snow thrower in case the

engine does not start.

• The battery run mode consumes battery power. Take care not to

operate the battery run mode for longer than 3 aggregate minutes
and operate it with the battery fully charged. Operating the battery
run mode for longer than 3 minutes or frequent operation will
discharge the batteries, which prevents you from starting the engine
and snow thrower.

• Be sure to turn the engine switch to the OFF position after starting

with the battery run mode. Leaving the engine switch at the ON
position will discharge the battery and may cause an accident.

• Recharge the battery as needed (see page 102).
• Be sure to set the main shift lever in the N (neutral) position before

starting the battery run mode.

• The snow thrower may not start under the following conditions.



Wheel pin(s) is/are broken or missing.



Battery is discharged.



Drive motor is faulty.

If necessary, move the snow thrower to a safe place by removing
the wheel pins (see page 120).

36V156410.book 73 ページ２０１８年１０月１０日　水曜日　午前１１時３０分

«
...
73
74
75
76
77
...
»

Содержание HSM1380i



































































































































Отзывы:

Нет отзывов

Похожие инструкции для HSM1380i

Бренд: ebm-papst Страницы: 11

Бренд: Best Страницы: 16

Optimax 9170-03-59

Бренд: Little Wonder Страницы: 14

Minute Mount 2 XV2 Series

Бренд: Fisher Страницы: 16

Бренд: ebm-papst Страницы: 11

Бренд: Troy-Bilt Страницы: 20

Snow Tracker 2690

Бренд: Troy-Bilt Страницы: 32

Бренд: Troy-Bilt Страницы: 46

Бренд: Gude Страницы: 32

Бренд: Gude Страницы: 40

Бренд: Toro Страницы: 164

Бренд: WEIBANG Страницы: 12

Бренд: Snapper Страницы: 14

Бренд: Snapper Страницы: 24

Бренд: Snapper Страницы: 24

Бренд: Snapper Страницы: 64

Бренд: Snapper Страницы: 78

PREMIUM 0503APESM1430

Бренд: VALERII S&M GROUP Страницы: 87

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды