Honda HSM1380i Скачать руководство пользователя | Manualshive

Страница: 69 / 130

background image

67

5) Push the auger clutch switch to

operate on the auger and blower.
• The indicator (green) comes

on when you push the auger
clutch switch.

• When the auger clutch switch

is pushed for three seconds or
longer, the protection function
gets armed. This stops the
auger and blower from turning.

• The auger and blower keep

turning while the drive clutch
lever is squeezed. Push the
auger clutch switch again to
stop the auger and blower.
(Interlocking operation of the
drive clutch lever and auger
clutch switch)

The auger and blower will start to turn when the drive clutch lever and
auger clutch switch is operated. Check around the snow thrower for
safety before operating the lever and switch.

6) Adjust the operating speed by

moving the main shift lever to a
position within the slow speed
range according to the volume
and nature of the snow, and
clear the snow.
• Even when you are clearing

the snow, adjust the operating
speed as needed by operating
the main shift lever according
to the change of the volume
and nature of the snow.

• When the snow is small in

volume or light in nature, move
the main shift lever to the high
speed side. Perform minor
adjustment of the main shift
lever to stabilize the operating
speed if necessary.

AUGER CLUTCH SWITCH

MAIN SHIFT LEVER

FAST

SLOW

SLOW

FAST

FAST
RANGE

LOW
RANGE

36V156410.book 67 ページ２０１８年１０月１０日　水曜日　午前１１時３０分

«
...
67
68
69
70
71
...
»

Содержание HSM1380i



































































































































Отзывы:

Нет отзывов

Похожие инструкции для HSM1380i

Бренд: Elektror Страницы: 28

Бренд: AL-KO Страницы: 168

Бренд: ARIETE Страницы: 45

Бренд: Jonsered Страницы: 272

Бренд: Black Max Страницы: 36

Бренд: Billy Goat Страницы: 12

Бренд: Unitary products group Страницы: 32

TurboTeuton P300

Бренд: Unigreen Страницы: 36

Бренд: Gude Страницы: 40

Бренд: Ukoke Страницы: 9

Бренд: LOFTNESS Страницы: 35

Бренд: LOFTNESS Страницы: 36

Бренд: LOFTNESS Страницы: 37

Бренд: LOFTNESS Страницы: 38

Бренд: LOFTNESS Страницы: 44

Бренд: Ventrac Страницы: 29

Бренд: M K Martin Enterprise Страницы: 27

Бренд: Cub Cadet Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды