Honda HSM1380i Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 130

background image

115

(3) Can not clear snow well.

SYMPTOM

POSSIBLE CAUSE

REMEDY

Hard to drive the
snow thrower in the
forward direction
while clearing the
snow.

Auger lock bolt is broken.

Replace the auger lock bolt (see
page 88).

Auger housing height is
not adjusted properly.

Adjust the auger housing height
in the proper position (see page
53).

Snow is stuck in the auger
and the related parts of
the snow thrower.

Remove the snow from the
underside of the auger housing
(see page 76).

Snow does not
come out from the
snow discharge
chute.

Snow discharge chute is
clogged.

Use the snow drop bar and
remove the snow from the snow
discharge chute (see page 76).

Hard to collect the
snow to clear.

Snow is stuck on the
auger.

Remove the snow from the
auger and the related parts (see
page 76).

Blower does not
rotate.

Blower lock bolt is broken.

Replace the blower lock bolt
(see page 88).

Drive motor overheated
by operation under
excessive load, which
armed the protection
function.

Release the drive clutch lever
and stop the work. Keep the
engine switch in the ON position
and wait until the drive control
warning indicator (orange) does
not blink (see page 71).

Auger clutch switch or
electromagnetic clutch is
faulty.

Consult an authorized Honda
dealer.

Auger does not
rotate.

Auger lock bolt is broken.

Replace the auger lock bolt (see
page 88).

Drive motor overheated
by operation under
excessive load, which
armed the protection
function.

Release the drive clutch lever
and stop the work. Keep the
engine switch in the ON position
and wait until the drive control
warning indicator (orange) does
not blink (see page 71).

Auger clutch switch or
electromagnetic clutch is
faulty.

Consult an authorized Honda
dealer.

36V156410.book 115 ページ２０１８年１０月１０日　水曜日　午前１１時３０分

«
...
115
116
117
118
119
...
»

Содержание HSM1380i



































































































































Отзывы:

Нет отзывов

Похожие инструкции для HSM1380i

Бренд: Poulan Pro Страницы: 44

Бренд: Shindaiwa Страницы: 28

Бренд: MTD Страницы: 28

Бренд: Poulan Pro Страницы: 44

Бренд: Toyama Страницы: 44

Бренд: Simplicity Страницы: 30

Бренд: Simplicity Страницы: 8

Бренд: Simplicity Страницы: 27

Бренд: Virnig Страницы: 20

Бренд: Dustbane Страницы: 2

Бренд: Dustbane Страницы: 8

Бренд: Toro Страницы: 12

38412 CCR 2400 GTS

Бренд: Toro Страницы: 24

Бренд: Toro Страницы: 24

Бренд: Toro Страницы: 36

Бренд: Milwaukee Страницы: 28

Бренд: Schiller Grounds Care Страницы: 32

Бренд: Desa Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды