manualshive.com logo in svg

Honda HSM1380i, Руководство пользователя

Поделиться
Скачать
Honda HSM1380i Скачать руководство пользователя страница 7

5

Operator responsibilities

• Know how to stop the snow thrower quickly, and understand the 

operation of all controls.

• Never permit anyone to operate the snow thrower without proper 

instruction. If people or pets suddenly appear in front of the snow 
thrower while it is in operation, immediately release the drive 
clutch lever to stop the snow thrower and avoid possible injury 
from rotating auger blades.

• Keep flames and sparks away from the batteries. 

Batteries produce explosive gas that can cause 
explosion.

• Handle the battery electrolyte with extreme care 

as it contains dilute sulfuric acid. Contact with 
your skin or eyes can burn you or cause loss of 
your eyesight.

• Do not allow children and other people to touch a 

battery unless they understand proper handling 
and hazards of the battery very well.

• Do not use a battery with the electrolyte at or 

below the lower level mark. It can explode 
causing serious injury.

• Wear the eye protection and rubber gloves when 

handling the batteries, or you can get burned or 
lose your eyesight by the battery electrolyte.

• Read this manual carefully and understand it 

before handling the batteries. Neglect of the 
instructions can cause personal injury and damage 
to the snow thrower.

36V156410.book  5 ページ  ２０１８年１０月１０日　水曜日　午前１１時３０分

Содержание HSM1380i



































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды