Honda HSM1380i Скачать руководство пользователя

Страница: 122 / 130

120

Emergency transport

You can move the snow thrower by pushing or pulling it without
engine power.

Place the snow thrower on the level ground after transportation and
use a new cotter pin when replacing the wheel pin.

1. Remove the cotter pins from the rear right and left wheels.
2. Remove the wheel pins from the rear right and left wheels.
3. The track rotates freely, allowing the operator to move the snow

thrower without engine power.

• Before removing the wheel pins, make sure to stop the rotating parts,

stop the engine and remove the engine switch key.

• Do not remove the wheel pins on the slope. The snow thrower may

move unintentionally, causing injury.

COTTER PIN

WHEEL PIN

36V156410.book 120 ページ２０１８年１０月１０日　水曜日　午前１１時３０分

Содержание HSM1380i



































































































































Результаты поиска

Содержание HSM1380i

Отзывы:

Похожие инструкции для HSM1380i

Бренды по названию

Популярные бренды

Honda HSM1380i, Руководство пользователя

Результаты поиска

Содержание HSM1380i

Отзывы:

Похожие инструкции для HSM1380i

Бренды по названию

Популярные бренды