Honda HS1132 Скачать руководство пользователя

Страница: 6 / 18

HS624 • HS724 • HS828 • HS928 • HS1132 SNOWBLOWERS

6 of 17

DAMAGE OR MISSING PARTS

• For parts lost or damaged in transit, refer to section 3 of the Warranty Policy and Procedures Manual.

• For parts left out by the factory, refer to section 6 of the Warranty Policy and Procedures Manual.

8 x 16 mm Bolt-Washer
(all except HS1132)

93404-08016-00

6 x 9 mm Spacer
(HS1132 only)

91502-ZE2-M90

8 x 41 mm Saddle-Head Bolt

(see

illustration)

90113-V10-000

8 mm Curved Square Washer

(see

illustration)

90501-898-000

8 mm flange Nut

(see

illustration)

94050-08000

8 mm Thin Flat Washer
(all except HS1132)

90412-738-E00

8 mm Flat Washer

94103-08000

Skid Shoe

HS724WA: SZBE-1054830 ~ subsequent
HS928WA/WAS: SZAS-1185559 ~ subsequent

76153-736-010

8 x 16 mm Bolt-Washer

HS724WA: SZBE-1054830 ~ subsequent
HS928WA/WAS: SZAS-1185559 ~ subsequent

93404-08016-00

Description

Quantity

Part Number

Illustration

TRACK-TYPE,

HS724 (4)

TRACK-TYPE,

ALL OTHERS (2)

TRACK-TYPE,

HS724 (4)

TRACK-TYPE

ALL OTHERS (2)

TRACK-TYPE,

ALL OTHERS (2)

TRACK-TYPE,

HS724 (4)

Содержание HS1132



















Результаты поиска

Содержание HS1132

Отзывы:

Похожие инструкции для HS1132

Бренды по названию

Популярные бренды

Honda HS1132, Инструкции дилера

Результаты поиска

Содержание HS1132

Отзывы:

Похожие инструкции для HS1132

Бренды по названию

Популярные бренды