background image

HS624 • HS724 • HS828 • HS928 • HS1132 SNOWBLOWERS

2 of 17

IMPORTANCE OF PROPER SETUP AND PRE-DELIVERY SERVICE

FOR YOUR CUSTOMER’S SAFETY

Proper setup and pre-delivery service are essential 
to the customer’s safety and the reliability of the 
snowblower. Any error or oversight made during 
assembly and servicing of a snowblower can result 
in faulty operation, damage to the snowblower, or 
injury to others.

FOR YOUR SAFETY

Some of the most important general safety 
precautions are given below. However, we cannot 
warn you of every conceivable hazard that can arise 
in performing setup and pre-delivery service. Only 
you can decide whether or not you should perform a 
given task.

  

 

IMPORTANT SAFETY PRECAUTIONS

•  Make sure you have a clear understanding of all basic shop safety practices and that you are wearing 

appropriate clothing and safety equipment. When performing setup and pre-delivery service, be 
especially careful of the following:

‰

Read all of the instructions before you begin, and make sure you have the tools, the replacement or 
repair parts, and the skills required to perform the tasks safely and completely.

‰

Protect your eyes by using proper safety glasses, goggles, or face shields any time you hammer, drill, 
grind, or work around pressurized air, pressurized liquids, springs, or other stored-energy 
components. If there is any doubt, put on eye protection.

‰

Use protective wear (gloves, safety shoes, etc.) when necessary. Handling hot or sharp parts can 
cause severe burns or cuts. Before you grab something that looks like it can hurt you, stop and put on 
gloves.

•  Make sure the engine is off before you begin any servicing procedures unless the instruction tells you to 

do otherwise. This will help eliminate several potential hazards:

‰

Carbon monoxide poisoning from engine exhaust–Be sure there is adequate ventilation whenever you 
run the engine.

‰

Burns from hot parts–Let the engine and exhaust system cool before working in those areas.

‰

Injury from moving parts–If the instruction tells you to run the engine, be sure your hands, fingers, and 
clothing are out of the way.

•  Gasoline vapors are explosive. To reduce the possibility of a fire or explosion, be careful when working 

around gasoline.

‰

Use only a nonflammable solvent, not gasoline, to clean parts.

‰

Never store gasoline in an open container.

‰

Keep all cigarettes, sparks, and flames away from all fuel-related parts.

B

 WARNING

Improper setup or pre-delivery service can 
create an unsafe condition that can cause 
your customer or others to be seriously hurt 
or killed.

Follow the procedures and precautions in 
this manual and other service materials 
carefully.

B

 WARNING

Failure to properly follow instructions and 
precautions can cause you to be seriously 
hurt or killed.

Follow the procedures and precautions in 
this manual carefully.

Содержание HS1132



















Отзывы: