background image

HS624 • HS724 • HS828 • HS928 • HS1132 SNOWBLOWERS

17 of 17

13.Fill out the appropriate areas of the Power Equipment Pre-Delivery Check List (TO056), and give the 

yellow copy to the customer.

PRE-DELIVERY (PDI) CHECK LIST

The following pre-delivery (PDI) check list is designed for general application. There are individual exceptions to this list. 
Refer to the appropriate set-up instructions and shop manuals for detailed procedures and specifications.

WHITE COPY

–Dealer

YELLOW COPY

–Customer

TO056

OTR50671-H (2010.11)

‰

ALL RECALLS AND UPDATES—Performed per Service Bulletins.

‰

ENGINE OIL—Fill to correct level with recommended oil. Remove 
“Engine has no oil” hang tag.

‰

FUEL TANK—Drain, inspect, and fill. Check for leaks.

‰

CARBURETOR FLOAT CHAMBER—Drain any old gasoline.

‰

CHECK THROTTLE OPERATION

‰

CHECK IDLE AND MAXIMUM ENGINE SPEED

‰

ACCESSORY INSTALLATION

‰

ALL NUTS, BOLTS AND OTHER FASTENERS—Check and tighten if 

necessary.

‰

AIR FILTER—Ensure the filter is properly seated.

‰

BATTERY—Check that the battery is FULLY charged (min 12.4V). 
Factory-activated batteries require a “top off.”

‰

Check maximum no-load engine speed (RPM______________)

‰

Check Auto Throttle®/Eco-Throttle™ operation

‰

Perform a load bank test

‰

Check the output from each receptacle

‰

UPON COMPLETION, check for fuel or oil leaks.

‰

AIR FILTER—Ensure the filter is properly seated.

‰

CLUTCH LEVER FREE PLAY—Adjust if necessary.

‰

BLADE CONTROL LEVER—Adjust if necessary.

‰

SMART DRIVE™ CABLE ADJUSTMENT—Check operation and adjust 
if necessary.

‰

HST CHANGE CABLE ADJUSTMENT—Check operation and adjust if 
necessary.

‰

MOWER HEIGHT ADJUSTMENT LEVERS—Check operation and set 
all adjustment levers to the same height.

‰

BLADE BOLTS—Check blade bolts for proper torque.

‰

ACCESSORY OR ATTACHMENT INSTALLATION

‰

ALL NUTS, BOLTS, AND OTHER FASTENERS—Check and tighten if 
necessary.

CHECK OPERATION

‰

UPON COMPLETION, check for fuel or oil leaks.

‰

AIR FILTER—Ensure the filter is properly seated.

‰

ACCESSORY INSTALLATION

‰

ALL NUTS, BOLTS AND OTHER FASTENERS—Check and tighten if 
necessary.

CHECK OPERATION (fill the primer chamber and check pump operation 
using a vacuum gauge)

‰

UPON COMPLETION, check for fuel or oil leaks.

‰

TRANSMISSION FLUID—Check the fluid level and check for leaks.

‰

CLUTCH LEVER FREE PLAY—Adjust if necessary.

‰

AUGER CLUTCH LEVER—Check free play and adjust if necessary.

‰

TIRE PRESSURE—Check for proper tire pressure.

‰

ACCESSORY INSTALLATION

‰

ALL NUTS, BOLTS AND OTHER FASTENERS—Check and tighten if 
necessary.

CHECK OPERATION

‰

UPON COMPLETION, check for fuel or oil leaks.

‰

AIR FILTER—Ensure the filter is properly seated.

‰

ACCESSORY INSTALLATION

‰

ALL NUTS, BOLTS AND OTHER FASTENERS—Check and tighten if 
necessary.

CHECK OPERATION

‰

UPON COMPLETION, check for fuel or oil leaks.

‰

AIR FILTER—Ensure the filter is properly seated.

‰

ACCESSORY INSTALLATION

‰

ALL NUTS, BOLTS AND OTHER FASTENERS—Check and tighten if 
necessary.

‰

CHECK Accessory Operation

‰

UPON COMPLETION, check for fuel or oil leaks.

‰

REVIEW THE PRE-DELIVERY CHECK LIST

‰

PROVIDE PRE-DELIVERY CHECK LIST (YELLOW COPY)

‰

PROVIDE AND REVIEW THE OWNER’S MANUAL

‰

EXPLAIN THE SAFETY PRECAUTIONS

‰

EXPLAIN THE PRE-OPERATION TASKS

‰

EXPLAIN THE OPERATION

‰

EXPLAIN THE MAINTENANCE INTERVALS

‰

EXPLAIN PROCEDURES FOR INFREQUENT USE AND SEASONAL 
STORAGE REGARDING FUEL & BATTERY (as applicable)

‰

EXPLAIN SERVICE HOURS AND CONTACT INFO

‰

PROVIDE AND REVIEW THE 

DISTRIBUTOR’S LIMITED WARRANTY 

COVERAGE AND POLICIES

‰

FILL OUT THE OWNER’S SALES REGISTRATION CARD

The operation of this unit was reviewed with me by a representative of the 
dealership. I have reviewed and understand the warranty policy. I have visually 
inspected the unit and found no defects or damage.

ALL PRODUCTS

GENERATORS

RATED LOAD (AC)

VOLTS

AMPS

FREQUENCY

DC BATTERY CHARGE SYSTEM

LAWN MOWERS

‰

Governor

‰

Flywheel Brake

‰

Roto-Stop®

‰

Engine Stop 
Switch

‰

Shift Lever

‰

Accessory or 
attachment

PUMPS

‰

Vacuum reading: __________

‰

Governor

‰

Accessory

DEALER
NAME

DEALER
NO.

MODEL
NAME

INSPECTION/TESTS 
PERFORMED BY:

SNOWBLOWER/SNOWTHROWERS

‰

Governor

‰

Drive Clutch

‰

Auger Clutch

‰

Shift Lever

‰

Accessory

TILLERS

‰

Throttle lever

‰

Clutch lever

‰

Accessory

‰

Tine/drive clutch

‰

Shift lever

TRIMMERS/BRUSHCUTTERS

UPON DELIVERY TO CUSTOMER

CUSTOMER
NAME

ADDRESS

CITY

STATE

ZIP
CODE

PHONE  (               )

DATE

SIGNATURE

FRAME SERIAL #:

ENGINE SERIAL #

NEW

NEW

Содержание HS1132



















Отзывы: