Holtek BC45B4523 Скачать руководство пользователя страница 30

Страница: 30 / 96

Rev. 1.20

October 28, 2020

BC45B4523

Bit 0

ParityEn

0: No parity bit is inserted or expected (ISO14443B and ISO15693)

1: The parity is inserted in the transmitted data stream at the end of each byte and expected in the

received data stream (ISO14443A)

• CRCPresetMSB Register

This register contains the most significant byte of the 16-bit preset value of the CRC Register.

Address

Bit

0x23

Name

CRCPresetMSB[7:0]

Type

R/W

Reset Value

Bit 7~0

CRCPresetMSB[7:0]

: The most significant byte of the CRC preset value

• CRCPresetLSB Register

This register contains the least significant byte of the 16-bit preset value of the CRC Register.

Address

Bit

0x24

Name

CRCPresetLSB[7:0]

Type

R/W

Reset Value

Bit 7~0

CRCPresetLSB[7:0]

: The least significant byte of the CRC preset value

• ADCCtrl Register

This register is used to setup the ADC control for field detection and card detection operation.

Address

Bit

0x25

Name

—

ADC_Delay[1:0] FD_MinLvl ADC_FastMode ADC_Rsln Reserved

Type

—

R/W

Reset Value

—

Bit 7~6 Unimplemented, read as “0”
Bit 5~4

ADC_Delay[1:0]

: Define ADC delay time

00: 76μs
01: 151μs
10: 227μs
11: 302μs

This bit field is used to define delay time for starting ADC conversion after all related analog circuits

are enabled. Refer to the “RF Amplitude Detector System” section for details.

Bit 3

FD_MinLvl

: Define step size of ADC in Field Detection operation

0: 7 bits – 10.6mV when ADC_Rsln=“0”; 8 bits – 5.3mV when ADC_Rsln=“1”
1: ADC is internally configured to 8 bits with 2.7mV resolution

This bit is used for additional configure of ADC resolution in Field Detection operation. Refer to the “RF

Amplitude Detector System” section for details.

Bit 2

ADC_FastMode

: Define the ADC mechanism and timing for conversion

0: Normal operation

1: Fast operation

If this bit is set to 1, the fast mode will be enabled, in which the conversion time can be reduced,

however the resolution is maintained. The ADC circuit is internally configured to 8-bit resolution when

this bit is set. Refer to the “RF Amplitude Detector System” section for more details.

Содержание BC45B4523

































































































Результаты поиска

Содержание BC45B4523

Отзывы:

Holtek BC45B4523, Руководство пользователя, Страница: 30 / 96

Результаты поиска

Содержание BC45B4523

Отзывы: