HOLT AN-6130PCIe MIL-STD 1553 Скачать руководство пользователя страница 9

Страница: 9 / 43

AN-6130PCIe

HOLT INTEGRATED CIRCUITS

Status Inputs (R only) - 0x2800-0000

BIT

FIELD

“A4”

SW2-5

SW2-4

SW2-3

SW2-2

SW2-1

“D5”

AUTOEN

BIT

FIELD

N/A

IRQ

RT2MC8 RT1MC8

WAIT

READY MTPKTRDY ACTIVE

ACTIVE

HI-6130 outputs a high when the BC or RT is processing a 1553 message.

MTPKTRDY

HI-6130 output. Monitor Packet active high when message complete.

READY

HI-6130 output. Set high when the host can configure the device.

WAIT

HI-6130 output. Not used by this design.

/RT1MC8

HI-6130 output. Outputs a pulse when a Mode Code 8 is received.

/RT2MC8

HI-6130 output. Outputs a pulse when a Mode Code 8 is received.

/IRQ (6130) HI-6130 interrupt output.

N/A

Not defined.

AUTOEN

Set by the SW2 DIP switch 6. Input to HI-6130 for auto initialization from
EEPROM.

“D5”

Not used by connected to a pad on the PCB from “D5” to the CPLD.

D10

SW2-1

DIP SWITCH user defined.

D11

SW2-2

DIP SWITCH user defined.

D12

SW2-3

DIP SWITCH user defined.

D13

SW2-4

DIP SWITCH user defined.

D14

SW2-5

DIP SWITCH user defined.

D15

“A4”

Not used but is connected to a pad from “A4” to the CPLD.

Secondary Output Latches R/W – 0x2C00-0000

BIT

15-D5

FIELD

N/A

RT2LOCK RT2SSF

MTSTOFF RT1LOCK RT1SSF

RESET

N/A

RT1SSF

RT1 Subsystem Fail input.

RT1LOCK

RT1 RT address input lock input.

MTSTOFF

HI-6130 memory test disable. Set low by internal pull-down resistor.

RT2SSF

RT2 Subsystem Fail input.

RT2LOCK

RT2 RT address input lock input.

D5:D15 N/A

Not defined.

Содержание AN-6130PCIe MIL-STD 1553












































Результаты поиска

Содержание AN-6130PCIe MIL-STD 1553

Отзывы:

Похожие инструкции для AN-6130PCIe MIL-STD 1553

Бренды по названию

Популярные бренды

HOLT AN-6130PCIe MIL-STD 1553, Руководство пользователя

Результаты поиска

Содержание AN-6130PCIe MIL-STD 1553

Отзывы:

Похожие инструкции для AN-6130PCIe MIL-STD 1553

Бренды по названию

Популярные бренды