HobbyKing AT-6 Texan Скачать руководство пользователя | Manualshive

Страница: 16 / 20

background image

16

The pilot’s feet provide further assistance in that when the canopy is secured the pilot’s
feet securely hold the battery in location.

No Velcro is used.

Sound Module

A ply wood plate was made – 1.5 mm ply –about 75mm x 35mm - onto which the sound
module is secured.

There was meant to be a wooden plate provided (as per the “manual”) but that was missing.

CA is used in the screw holes to assist in strength.

The plate with the sound module attached is then secured across one of the new openings
made in the “floor” between upper and lower spaces of the fuselage.

«
...
14
15
16
17
18
...
»

Содержание AT-6 Texan





















Отзывы:

Нет отзывов

Похожие инструкции для AT-6 Texan

Ultimate EP 3D Profile

Бренд: E-FLITE Страницы: 40

Бренд: AeroWorks Страницы: 17

Education STEM Explorations 79320

Бренд: K'Nex Страницы: 16

Бренд: Eduard Страницы: 4

Бренд: MTHTrains Страницы: 36

Бренд: Fisher-Price Страницы: 32

Barbie Babysitter

Бренд: Mega Bloks Страницы: 28

Tank Car 4-axle 67230

Бренд: BRAWA Страницы: 4

Super Chief Xtra DCS100

Бренд: Digitrax Страницы: 119

Бренд: M.T.H. Страницы: 96

Panther Ausf. D handles and holders

Бренд: Eduard Страницы: 4

Бренд: Fisher-Price Страницы: 4

Бренд: Air Hogs Страницы: 4

WILD THINGS Series

Бренд: Fischer-Price Страницы: 2

Бренд: bewello Страницы: 12

Disc-Oh Flyers BX1592

Бренд: B.toys Страницы: 2

TWISTER Rave Hoopz

Бренд: Hasbro Gaming Страницы: 2

Бренд: Black Horce Model Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды