background image

 

PRODUCT ID: 9041000151 
 

Features:

 

• Plug and Fly, simply add your own battery and radio system 
• Engine Sound Module System included 
• Fully functional split flaps 
• Electronic servoless retracts 
• High level of scale detail 
• Ultra-durable EPO foam construction 
 
General 

 
The model is of good finish and pleasing appearance although some features of the 
construction and assembly leave a bit to be desired. 
 

Manual / Instruction book 

 
Manual does not describe the model as it is purchased. Differences are to be noted with 
regard to the sound system in particular.  
 

Issues Encountered on Assembly 

 
Speed control failed on powering up – replaced (by way of account credit) by HobbyKing, 
One flap servo inoperative on arrival - replaced (by way of account credit) by HobbyKing, 
Missing sound module mount - replaced (by way of account credit) by HobbyKing. 
 
As noted above the manual provided seems not to be for this specific variant of the “Texan” 
which was also disappointing. The content of the manual specifically related to the sound 
system is not related to this model. 
 
Both of these aspects have been referred to HobbyKing with advices from them that 
corrections will be made although as of compiling this note nothing has been noted on the 
website in the files section. 
 

Build Record 

 
I have maintained a photographic build record of my construction of this model and whilst 
in no way do I feel it covers all the possibilities that may exist – or methods that might be 
utilised – I have done this to assist others in my recognising the shortcomings of the 
provided documentation and the difficulties they may cause. 
 
A number of the modifications have been gleaned from other sources on the WWW with 
some of them copied / varied by myself in an effort to further improve the build and 
hopefully the longevity and flying capabilities of the aircraft. 
 
This note is current as of October 7, 2013.  
 

Содержание AT-6 Texan





















Отзывы: