HobbyKing AT-6 Texan Скачать руководство пользователя | Manualshive

Страница: 18 / 20

background image

18

Sound Module with cover removed

Curiosity got the better of me so I removed the sound module cover to inspect.

There is no volume control that I recognise as such.

The cover was refitted.

Cabling of the module is straightforward and there is now additional information on the HK
website although reference is still made to volume control. Not sure where the heat sink is
either.

Information is located at “hardware and accessories/ audio systems and parts” in the files
section for the PNP Engine Sound Module System.

FINAL WEIGHT

Final weight of aircraft was 1620 grams with the Donkey style motor fitted.

Donkey style motor weight is 136 grams.

This weight includes the battery – see above – the pilot and the modifications effected as
described above including revised battery size and larger ESC.

«
...
16
17
18
19
20
»

Содержание AT-6 Texan





















Отзывы:

Нет отзывов

Похожие инструкции для AT-6 Texan

Бренд: Bachmann Страницы: 12

Gourmet Kitchen

Бренд: Naomi Kids Страницы: 20

St. Canute "700"

Бренд: Billing Boats Страницы: 28

Бренд: marklin Страницы: 24

Rudolph the Rocking Reindeer 4827

Бренд: Step2 Страницы: 4

Бренд: Faller Страницы: 8

Battleship Tirpitz

Бренд: REVELL Страницы: 30

BATTERY BUS, SETRA S 315

Бренд: Faller Страницы: 2

Бренд: marklin Страницы: 32

SOPWITH CAMEL F.1

Бренд: Model Airways Страницы: 28

Бренд: Walkera Страницы: 22

Бренд: Multiplex Страницы: 11

3D Puzzle Chrysler Building Night Edition

Бренд: Ravensburger Страницы: 4

Бренд: Velleman Страницы: 9

Smart Start Future

Бренд: VTech Страницы: 16

Бренд: WattAge Страницы: 32

AquaCraft ATLANTIC Harbor Tugboat

Бренд: Hobbico Страницы: 8

Бренд: Jamara Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды