HobbyKing AT-6 Texan Скачать руководство пользователя | Manualshive

Страница: 17 / 20

background image

17

The sound module cables and other cables are immediately below the module and
connection is very straight forward given the easy access now afforded with the additional
openings.

Receiver

The receiver is mounted on the floor immediately in front of the aft seat in the cockpit.
Again cable access is now reasonably generous. With the receiver visible in the cockpit
binding is more straight forward.

Electronic Speed Control

The original ESC failed on powering up and was replaced with a Turnigy Plush 40 ampere
unit which is slid into the original location.

The Plush ESC unit is a little larger and is as a result a bit tight in place but increased air flow
in the area should minimise heating issues.

Servos

One flap servo was DOA so both were replaced with HobbyKing 928BB units.

For information investigation as to the details of the original flap servos - with HK –
indicated that the originals are Turnigy TSS - 9S slow speed servos.

«
...
15
16
17
18
19
...
»

Содержание AT-6 Texan





















Отзывы:

Нет отзывов

Похожие инструкции для AT-6 Texan

Ultimate EP 3D Profile

Бренд: E-FLITE Страницы: 40

Бренд: Eachine Страницы: 8

Бренд: GRAUPNER Страницы: 42

Бренд: 3D AEROWORKS Страницы: 26

Бренд: VTech Страницы: 16

Bbaby Mini Woofer BX1986

Бренд: Maison Battat Страницы: 2

Zoom Avia B.534 IV. Series Weekend

Бренд: Eduard Страницы: 2

Бренд: Odyssey Страницы: 2

Бренд: VTech Страницы: 8

Seaview Voyage To The Bottom Of The Sea PGX160

Бренд: ParaGrafix Страницы: 2

Бренд: Fisher-Price Страницы: 2

Бренд: Opitec Страницы: 7

Бренд: Fisher-Price Страницы: 5

AXN Floater Jet

Бренд: H-KING Страницы: 18

Бренд: Mega Bloks Страницы: 20

ROCKWELL AERO COMMANDER SHRIKE

Бренд: Black Horse Model Страницы: 30

Бренд: Faller Страницы: 12

E-flite UMX NIGHT VAPOR BNF

Бренд: Horizon Hobby Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды