HMS Anybus-X Скачать руководство пользователя страница 17

Страница: 17 / 86

Chapter 3

Configuration 3-1

AB7665 User manual

Configuration

This chapter describes how the Anybus-X Ethernet to J1939 Gateway is config-

ured using the Anybus-X Configuration Tool (BWConfig). Detailed descriptions

of each configurable parameter in the gateway are provided as well as how they

are set in the tool.

The next chapter walks the reader through the configuration of an example appli-

cation to illustrate how the configurable parameters are used in a real-world appli-

cation.

Anybus-X Configuration Tool (BWConfig)

The Anybus-X Configuration Tool allows you to configure the parameters associ-

ated with the Ethernet and J1939 network interfaces as well as to set up the con-

tents and layout of the I/O table.

BWConfig is a Microsoft Windows application that communicates with a Any-

bus-X over a standard RS-232 serial link using the PC serial port. BWConfig is

compatible with Microsoft Windows 95, 98, NT, 2000, and XP.

Installing the Tool

Install BWConfig from the CD by running

Setup.exe

which is found in the CD's

root directory.

If you have downloaded BWConfig from the web site, unzip the downloaded file

into a temporary directory and run

Setup.exe

which is found in the temporary

directory.

Содержание Anybus-X























































































Результаты поиска

Содержание Anybus-X

Отзывы:

Похожие инструкции для Anybus-X

Бренды по названию

Популярные бренды

HMS Anybus-X, Руководство пользователя

Результаты поиска

Содержание Anybus-X

Отзывы:

Похожие инструкции для Anybus-X

Бренды по названию

Популярные бренды