Hitachi KP-FD30, Руководство по эксплуатации

Страница: 7 / 17

16.White balance Selectable in 3 modes
ATW / AWC / MANUAL
17.Text display
24 alpha-numeric characters in one line
18.Camera setting menu
Mode selection, quality-of-image adjustment
19.Remote control
RS-232C level (MULTI Connector)
20. Power supply DC +12V ± 10%
21. Power
consumption
Approx. 360mA
(Including 60mA for auto-iris lens)
22.Lens mount
C/CS mount ( Frange-back adjustment )
23. Ambient
temperature
Operating -10
～
+50
℃
/30
～
80%RH
(*3)
Storage -20 ～ +60 ℃ /20 ～ 90%RH
(*3)
Note : If operated continuously, be sure to use at less than
+40 (104F) for long term stable performance.
24. Vibration
endurance 68.65 m/s ( 10 to 200Hz, 30 minutes each on
XYZ axes )
2
(*4)
(*4)
Note : Do not subject to strong vibration for long periods of time.
25. Shock
endurance 490.3 m/s ( vertical, horizontal, once each
face )
2
26. External
dimensions 58(W) x 58(H) x 48(D) mm
( not including lens and protrusions )
27.Mass Approx. 220g ( without lens )
12. Sensitivity
selection
AGC OFF/ON
Manual Gain Adjustable at AGC OFF.
Limit Gain Adjustable at AGC ON
(0
～
Approx. 18dB)
13.Electric shutter speed
PRESET Select high speed shutter:OFF(1/60),1/100,
1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000, 1/20000
1/30000, 1/50000 second
(*2)
low speed shutter:OFF(1/60),1/30,
1/15, 1/10, 1/7.5, 1/6, 1/5, 1/3.75
1/3, 1/2.5, 1/1.5, 1, 1.5, 2, 2.5, 3,
3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8 second
(*2)
An image output becomes intermittent.
VARIABLE Approx. 1H steps from 1/60 second to 1/10,000
second
AES 1/60 sec
～
Approx.1/50000 sec
From 1/60 second to approx. 1/50,000 second
SLOW/NORMAL/FAST
EXT. TRIG ONE trigger / Fixed shutter
14.Auto level control[ALC]
AVERAGE
PEAK&AVERAGE
AREA
(Scanning area is selectable from 9 area.)
15.Auto-iris lens outputs
Iris control voltage input (galvanometer) type lens
Damper 1150-ohm±10%
Coupling coil
impedance Drive 190-ohm±10%
6 ． Video signal
output
RGB output RGB 0.7 Vp-p/75-ohm Positive
SYNC (G on SYNC) 0.3 Vp-p Negative
MULTI connector (D-sub15)
Y/C output
(*1)
Y 0.7 Vp-p/75-ohm Positive
SYNC 0.3 Vp-p Negative
C 0.3 Vp-p(Burst)/75-ohm
Subcarrier frequency 3.579545MHz
MULTI connector ( D-sub15 )
VBS output
(*1)
Video 0.7 Vp-p/75-ohm Positive
SYNC 0.3 Vp-p Negative
Burst 0.3 Vp-p 8 cycles
Subcarrier frequency 3.579545MHz
MULTI connector ( D-sub15 )/BNC
7 ． Video signal
processing
Digital processing ( input 10 bits )
8
．
S/N ( Y signal ) More than 50dB
( AGC, enhancer and gamma off )
9
．
Resolution Horizontal 440TV lines
( Y signal at center ) Vertical 480 TV lines (350 TV lines(*))
10
．
Standard
sensitivity
2,000 lx (F5.6, 100IRE)
11 ． Minimum illumination
10 lx ( F1.4, AGC ON, 50IRE )
(*1)
Only at the NTSC mode
1 ． Imaging device 1/2-inch progressive scan interline CCD
Total number of
pixels 692(H) x 504(V)
No. of effective
pixels
659(H) x 494(V)
Unit cell size 9.9(H) x 9.9(V)
μ
m ( Square pixel )
Color filter R, G, B primary color mosaic filters on chip
2
．
Scanning area 6.52(H) x 4.89(V)mm
3 ． Scanning
system
Progressive scan ( VGA mode )
(Switch change) 2:1 interlace scan ( NTSC mode )
4
．
Frequency Horizontal 31.468kHz (15.734kHz
(*1)
)
±
0.5Hz
Vertical 59.94Hz
5
．
Sync system Internal / external ( HD/VD auto selection
(*1)
)
Internal sync
output
HD 31.468kHz (15.734kHz
(*1)
)
±
0.5Hz
(Switch change) 2Vp-p/75-ohm or 5Vp-p Negative
VD 59.94Hz
(Switch change) 2Vp-p/75-ohm or 5Vp-p Negative
SYNC 2Vp-p/75-ohm Negative
WEN 5Vp-p Negative
External sync
input
HD 31.468kHz (15.734kHz
(*1)
)
±
0.5Hz
2 ～ 5Vp-p Negative
VD 59.94Hz 2
～
5Vp-p Negative
TRIG Low 0 Vdc High 2 ～ 5Vdc
Main specifications