Hitachi CS 33ED Скачать руководство пользователя страница 6

Страница: 6 / 44

-5-

Dirty or faulty spark plug

Clean/replace.

Defective air gap

Adjust.

Worn piston ring

Replace.

Worn piston

Replace.

Worn cylinder

Replace.

Expired oil seal service life

Replace.

Revolutions low for idling

Adjust.

Poorly adjusted carburetor ass’y

Adjust.

Defective sealing of the packing

Replace.

Revolutions low for idling

Adjust.

Poorly adjusted carburetor ass’y

Adjust.

Defective sealing of the packing

Replace.

Revolutions too high for idling

Adjust.

Worn or faulty clutch

Inspect/replace.

Poorly adjusted carburetor ass’y

Adjust.

Clogged fuel filter

Clean/replace.

Inadequate warm-up, especially in cold
weather

Warm up.

Poorly adjusted carburetor ass’y

Adjust.

Defective sealing of the packing

Replace.

Clogged cylinder vent passage, exhaust port
or carbon-clogged muffler

Clean.

Clogged air cleaner

Clean.

Chain brake set on

Release.

Poorly adjusted carburetor ass’y

Adjust.

Faulty carburetor ass’y pump diaphragm

Replace.

Dirt-clogged carburetor ass’y

Clean.

Dirt-clogged high-speed fuel line of the
carburetor ass’y

Clean.

Air intake from the packing section

Inspect.

Faulty carburetor ass’y pump diaphragm

Replace.

Poorly adjusted carburetor ass’y

Adjust.

Revolutions low for idling

Adjust.

Poorly adjusted carburetor ass’y

Adjust.

Defective sealing of the packing

Replace.

Clogged air cleaner

Clean.

Poorly adjusted carburetor ass’y

Adjust.

Does the engine stop when
the speed rapidly decelerates
from high speed?

Yes

Does the engine stop by
pulling the throttle lever?

Does the speed increase
by pulling the throttle lever?

Are revolutions fluctuated
during acceleration?

Tilt the tool during idling.
Does the engine stop?

Yes

Does the saw chain rotate
during idling?

Yes

Start the tool and set to
idling mode.
Does the engine stop?

Is fuel consumption
excessive?

Yes

Содержание CS 33ED













































Результаты поиска

Содержание CS 33ED

Отзывы:

Похожие инструкции для CS 33ED

Бренды по названию

Популярные бренды

Hitachi CS 33ED, Руководство по обслуживанию

Результаты поиска

Содержание CS 33ED

Отзывы:

Похожие инструкции для CS 33ED

Бренды по названию

Популярные бренды