Hitachi CS 33ED Скачать руководство пользователя страница 10

Страница: 10 / 44

-9-

2. Disassembly and reassembly of the front handle

[Tools required]

• Phillips screwdriver

• Flat-blade screwdriver

• Box-end wrench 10 x 19 mm

• Socket wrench (10 mm)

(1) Disassembly

• Use a Phillips screwdriver to remove the two Tapping Screws (W/Flange) D5 x 25 (Black)

[193]

. Use

a flat-blade screwdriver to remove the Flange Nut M6

[165]

and then use a box-end wrench 10 x 19

mm to remove the Front Handle

[195]

(See the figure “Tightening the Flange Nut M6

[165]

” on the

next page.)

• Use a 1

0-mm wide box wrench (socket type) to remove the Antivibration Spring

[161]

(2) Reassembly

Reassembly can be conducted by reversing the disassembly procedure. However, special attention

should be given to the following items.

• Reassemble the anti-vibration mechanism of the Front Handle

[195]

by following the procedure

below.

• Front handle

Front Handle

[195]

Flange Nut M6

[165]

Spring Holder

[159]

Damper Set Bolt

[197]

Bolt Washer M6

[62]

Antivibration Spring

[161]

Spring Cover

[196]

Tapping Screw (W/Flange)
D5 x 25 (Black)

[193]

Содержание CS 33ED













































Результаты поиска

Содержание CS 33ED

Отзывы:

Похожие инструкции для CS 33ED

Бренды по названию

Популярные бренды

Hitachi CS 33ED, Руководство по обслуживанию

Результаты поиска

Содержание CS 33ED

Отзывы:

Похожие инструкции для CS 33ED

Бренды по названию

Популярные бренды