Hitachi CS 33ED Скачать руководство пользователя страница 23

Страница: 23 / 44

-22-

• Engine ass’y

10. Disassembly and reassembly of the engine ass’y

[Tools required]

• Long-nose pliers

• Hex. bar wrench (5 mm)

• Box-end wrench 10 x 19 mm

(1) Disassembly

Remove the recoil starter, cleaner, muffler, clutch, and pump ass’y before disassembling the engine

ass’y.

• Use long-nose pliers to pull out the Spark Plug Cap

[77]

from the Spark Plug Ass’y BPMR7A

[73]

• Use the 19-mm side of the box-end wrench 10 x 19 mm to remove the Spark Plug Ass’y BPMR7A

[73]

• Loosen the two Hex. Socket Bolts M4

[26]

and remove the Intake

[27]

• Loosen the five Seal Lock Hex. Socket Bolts (W/Washers) M5

[29]

(upper side x 2 pcs., lower side x 2

pcs., and lateral side x 1 pc.), and then remove the engine ass’y.

(2) Reassembly

Reassembly can be conducted by reversing the disassembly procedure. However, special attention

should be given to the following items.

• Do not reuse the Hex. Socket Bolt M4

[26]

and Seal Lock Hex. Socket Bolts (W/Washers) M5

[29]

• Insert the high tension cord into the Spark Plug Cap

[77]

, and then attach the Metal Fitting of Plug

Cap (A)

[80]

to the high tension cord.

• Pass the high tension cord through the hole on the engine case.

• Attention must be paid to the position of the Intake Packing

[28]

when mounting the Intake

[27]

• Spark plug cap

Spark Plug Cap

[77]

Metal Fitting of Plug Cap (A)

[80]

High tension cord

Spark Plug Cap

[77]

Spark Plug Ass’y BPMR7A

[73]

Intake

[27]

Intake Packing

[28]

Hex. Socket Bolt M4

[26]

Seal Lock Hex. Socket Bolts
(W/Washers) M5

[29]

Seal Lock Hex. Socket Bolts
(W/Washers) M5

[29]

Seal Lock Hex. Socket Bolt
(W/Washers) M5

[29]

Engine ass’y

Cord Insulation
Tube L100

[75]

Содержание CS 33ED













































Результаты поиска

Содержание CS 33ED

Отзывы:

Похожие инструкции для CS 33ED

Бренды по названию

Популярные бренды

Hitachi CS 33ED, Руководство по обслуживанию

Результаты поиска

Содержание CS 33ED

Отзывы:

Похожие инструкции для CS 33ED

Бренды по названию

Популярные бренды