Hitachi CS 33ED Скачать руководство пользователя страница 4

Страница: 4 / 44

-3-

This section describes repair, focusing on portions requiring frequent repair. See the TROUBLESHOOTING

GUIDE in the previous section as the context for the following descriptions.

1. Precautions on maintenance, inspection and repair

•

The fuel used readily ignites; therefore, never bring the product near a flame.

•

Use new gaskets at reassembly.

• Prior to disassembly for repair, remove the fuel and chain oil into separate containers, and allow the tool to

cool down.

• During repair, startup or running, use adequate care for portions posing the risk of burn injury or electric

shock, such as hot areas including the muffler, high voltage cord, and spark plug.

• Before running the tool with the guide bar and saw chain attached, make sure that there are no other

people nearby.

• Ensure proper ventilation when performing repair in a small room or other poorly ventilated space.

• After repair, confirm that the throttle lever returns to the idling state and the engine stops when the stop

switch is turned to the stop position.

2. Inspection criteria for each section and consumable parts

Model

Item

CS 33EDP/CS 33ED

Idling revolutions

2,800 to 3,200 min

-1

No-load maximum revolutions
(with guide bar and saw chain)

12,500 to 13,500 min

-1

Clutch engagement

4,000 to 4,800 min

-1

Accelerating performance

Smooth acceleration

Gap between magneto rotor and
ignition coil ass’y

0.2 to 0.4 mm

Spark plug

NGK BPMR7A

Gap between spark plug electrodes

0.6 to 0.7 mm

Saw chain type

OREGON 91PX

Saw chain pitch x gauge

3/8” (9.53 mm) x 0.05” (1.27 mm)

No. of saw chain drive links

52 or 57

REPAIR GUIDE

Содержание CS 33ED













































Результаты поиска

Содержание CS 33ED

Отзывы:

Похожие инструкции для CS 33ED

Бренды по названию

Популярные бренды

Hitachi CS 33ED, Руководство по обслуживанию

Результаты поиска

Содержание CS 33ED

Отзывы:

Похожие инструкции для CS 33ED

Бренды по названию

Популярные бренды