Hitachi CS 33ED Скачать руководство пользователя страница 26

Страница: 26 / 44

-25-

CAUTION: Any soot remaining in the Cylinder [74] may cause contact between Piston (M) [86]

and the Cylinder [74], resulting in a malfunction.

• Completely remove liquid packing (ThreeBond 1207C) on the contacting surfaces of the Crank Case

[96]

and Cylinder

[74]

. At that time, be careful not to damage the contacting surfaces.

• Completely remove liquid packing (ThreeBond 1207C) on the contacting surfaces of the Cylinder

[74]

Scavenging Cover (A)

[84]

, and Scavenging Cover (B)

[70]

. At the time, be careful not to damage the

contacting surfaces.

• Before applying new liquid packing (ThreeBond 1207C) on the contacting surfaces of the Cylinder

[74]

Scavenging Cover (A)

[84]

, and Scavenging Cover (B)

[70]

, completely degrease the contacting

surfaces.

• Before mounting the Crank Shaft

[93]

, apply 0.2 to 0.6 gram of 2-cycle oil to the inside of the Cylinder

[74]

and the periphery of Piston (M)

[86]

• Before applying new liquid packing (ThreeBond 1207C) on the contacting surfaces of the Cylinder

[74]

and Crank Case

[96]

, completely degrease the contacting surfaces.

13. Disassembly and reassembly of the piston and piston ring

[Tools required]

• Long-nose pliers

• J-359 jig (No. 6695741) (piston pin extraction tool ass’y)

(1) Disassembly

Remove the Crank Worm Ass’y

[89]

from the Cylinder

[74]

before disassembly.

• Use long-nose pliers to remove the two Circlips

[85]

• Insert a hex. socket hd. bolt M5 x 12 into the

pushing side of the Piston Pin

[88]

, and then turn

the pin pullout bolt of the J-359 jig (piston pin

extraction tool ass’y) clockwise to pull out

the

Piston Pin

[88]

CAUTION: Do not scratch Piston (M) [86].

• Remove the Piston Ring (XR1-1856)

[87]

from

Piston (M)

[86]

by widening the gap of the piston

ring so as not to damage the periphery of the

piston. (When the Piston Ring (XR1-1856)

[87]

firmly adhered, insert a gap gauge (T0.3)

between the Piston Ring (XR1-1856)

[87]

and

Piston (M)

[86]

, and then remove the piston ring.)

• Cylinder and scavenging covers

•

Removing the piston

Hex. socket hd.
bolt M5 x 12

Pin pullout bolt

J-359 jig
(piston pin extraction tool ass’y)

Crank Case

[96]

Hex. Socket Hd. Bolt
(W/Sp. Washer) M5 x 18

[95]

Crank Shaft

[93]

Piston

Ball Bearing

[92]

Worm

[90]

Oil Seal

[91]

Oil Seal

[91]

Cylinder

[74]

Scavenging Cover (B)

[70]

Scavenging Cover (A)

[84]

Hex. Socket Hd. Bolt M4 x 10

[69]

Hex. Socket Hd. Bolt M4 x 10

[69]

Crank Worm Ass’y

[89]

Ball Bearing

[92]

Содержание CS 33ED













































Результаты поиска

Содержание CS 33ED

Отзывы:

Похожие инструкции для CS 33ED

Бренды по названию

Популярные бренды

Hitachi CS 33ED, Руководство по обслуживанию

Результаты поиска

Содержание CS 33ED

Отзывы:

Похожие инструкции для CS 33ED

Бренды по названию

Популярные бренды