background image

GAS CONNECTION 

IMPORTANT: The connection must be executed by qualified technician according to the 
relevant local standard. 

The connection must be executed by qualified technician according to the relevant standard. 
The fitting is made up of (see below figuration);

          1 Elbow fitting “A”

          1 adapter “B” 

           Gaskets “C”,”D”

           A built in gas hob must be installed

           in a room with adequate ventilation. 

ORIENTATION of the ELBOW

The appliance is supplied with a gas connection oriented towards the centre of the built-in gas 
hob.  The  connection  to  the  gas  supply  must  be  effected  only  from  this  side  or  in  vertical 
position by turning the elbow downwards. To turn the elbow, follow these operations:

 

 Loosen the nut

 

 Turn the elbow

 

 Lock the nut

 

 Make sure that there are no

          leakage by a soapy solution.

IMPORTANCES:

1.Never attempts to turn the elbow without having first slackened off the relative lock nipple.

2.The  seals  are  the  elements  that  guarantees  the  seal  in  the  gas  connection.  It  is 
recommended  that they be replaced  whenever  they shows  even  the slightest  deformation  or 
imperfection.

3.After  connecting  to  the  mains,  check  that  the  couplings  are  correctly  sealed,  using  soap 
solution, but never a naked flame.

4.The connection with rigid metal pipes should not cause stresses to the bob ramp.

5.If the rubber tube is used for the gas connection:

 

Make  sure  the  tube  is  snugly  fit  at  both  ends  and  use  a  standard  tube  clamp  (not 
supplied) to fasten it.

 

The rubber tube must be as short as possible, without contractions or kinks.

 

The rubber tube must never be at any point in its length in contact with the “hot” parts.

 

From time to time check to make sure that the rubber is in perfect condition.










9

Содержание HHU60GASS


















Отзывы: