Hioki PW8001-01 Скачать руководство пользователя страница 189

Страница: 189 / 262

183

Specifications of Input, Output, and Measurement

Synchronization

source

U1 to U8, I1 to I8, DC (fixed at the data refresh interval for DC only)

For the PW8001-1x, the model equipped with the motor analysis option

Ext1 to Ext4:

When the input settings of the following channels are set to Speed

(pulse input) and the remainder left over when the pulse count is

divided by half the number of poles is zero.

Ext1: Ch. B, Ext2: Ch. D, Ext3: Ch. F, Ext4: Ch. H

Zph1:

When the Ch. D input setting is set to Origin (pulse input)

Zph3:

When the Ch. H input setting is set to Origin (pulse input)

Ch. B, Ch. D, Ch. F, Ch. H:

When the corresponding channel enters

[Individual input]

operating

mode

•

Can be selected for each wiring configuration. (U and I of the same channel are

measured in sync with the same synchronization source.)

•

The zero-crossing point of the waveform after passing through the zero-cross filter is

used as the reference when U or I is selected.

Effective

frequency range

of synchronization

source

DC, 0.1 Hz to 2 MHz (up to 1 MHz for the U7001)

Effective input range

of synchronization

source

1% of range to 110% of range

Zero-cross filter

Used in zero-crossing detection for voltage and current waveforms. Does not affect

measured waveforms.

Consists of a digital LPF and HPF filters. Cutoff frequencies are automatically determined

based on the settings of the upper and lower frequency limits as well as measurement

frequencies.

Measurement lower

frequency limit

Choose from among the following frequency values for each wiring configuration:

0.1 Hz, 1 Hz, 10 Hz, 100 Hz, 1 kHz, 10 kHz, 100 kHz

Measurement upper

frequency limit

Choose from the following frequency values for each wiring configuration:

100 Hz, 500 Hz, 1 kHz, 5 kHz, 10 kHz, 50 kHz, 100 kHz, 500 kHz, 1 MHz, 2 MHz

Polarity detection

Voltage/current zero-crossing timing comparison method

Measurement item

Voltage (U), current (I), active power (P), apparent power (S), reactive power (Q),

power factor (

), phase angle (

), voltage frequency (fU), current frequency (fI),

efficiency (η), loss (Loss), voltage ripple factor (Urf), current ripple factor (Irf),

current integration (Ih), power integration (WP), voltage peak (Upk), current peak (Ipk)

See “10.4 Detailed Specifications of Measurement Parameters” (p. 203).

(2)

Specifications common to voltage measurement

See “10.6 U7001 2.5MS/s Input Unit” (p. 220) and “10.7 U7005 15MS/s Input Unit” (p. 225).

(3)

Specifications common to current measurement

See “10.6 U7001 2.5MS/s Input Unit” (p. 220) and “10.7 U7005 15MS/s Input Unit” (p. 225).

Specifications

HIOKI PW8001A961-00

Содержание PW8001-01







































































































































































































































































Результаты поиска

Содержание PW8001-01

Отзывы:

Похожие инструкции для PW8001-01

Бренды по названию

Популярные бренды

Hioki PW8001-01, Инструкция по эксплуатации

Результаты поиска

Содержание PW8001-01

Отзывы:

Похожие инструкции для PW8001-01

Бренды по названию

Популярные бренды