Hioki PW8001-01 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 262

background image

8

Safety Information

Safety Information

Please review the safety information below before using the instrument. Read this manual carefully
and ensure you understand its contents before using the instrument. Improper use of the instrument
could result in serious bodily injury or damage to the instrument.

Measurement categories

IEC 61010 defines measurement categories to facilitate safe use of measuring instruments. Test
and measurement circuits designed to be connected to a main power supply circuit are classified

into three categories depending on the type of main power supply circuit. A measuring instrument
that does not have a measurement category cannot be used to measure a main power supply
circuit.

DANGER

Do not use a measuring instrument to measure a main power supply

circuit whose category exceeds the instrument’s rated measurement

category.

Do not use a measuring instrument that does not have a rated

measurement category to measure a main power supply circuit.

Doing so may result in serious bodily injury or damage to the instrument or other

equipment.

No measurement

category

(O)

Applicable to the measurement of other circuits that are not directly connected to the

main power supply.

EXAMPLE: Measurement on the secondary-side equipment from the socket outlet of

fixed installation through a transformer, etc.

Measurement

category II

(CAT II)

Applicable to test and measuring circuits connected directly to utilization points (socket

outlets and similar points) of a low-voltage MAINS installation.

EXAMPLE: Measurements on household appliances, portable tools, and similar

equipment, and on the consumer side only of socket outlets in the fixed

installation.

Measurement

category III

(CAT III)

Applicable to test and measuring circuits connected to the distribution part of the a

building’s low-voltage MAINS installation.

Example: Measurements on distribution boards (including secondary meters),

photovoltaic panels, circuit breakers, wiring, including cables, bus-bars,

junction boxes, switches, and socket outlets in a fixed installation, as well as

equipment for industrial use and some other equipment such as stationary

motors with permanent connection to the fixed installation.

Measurement

category IV

(CAT IV)

Applicable to test and measuring circuits connected at the source of the a building’s low-

voltage MAINS installation.

Example: Measurements on devices installed before the main fuse or circuit breaker in

the building installation.

Outlet

CAT II

Interior wiring

Distribution panel

Service entrance

Service drop

CAT IV
Power meter

CAT III

Fixed equipment

HIOKI PW8001A961-00

«
...
12
13
14
15
16
...
»

Содержание PW8001-01







































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PW8001-01

Бренд: Parker Research Corp Страницы: 3

TEC SourceMeter 2510

Бренд: Keithley Страницы: 244

Бренд: Kawai Страницы: 112

HF Scientific AccUView LED Ex

Бренд: Watts Страницы: 2

Бренд: A&D Страницы: 68

iNELS Air AirCFS-100S

Бренд: Elko Страницы: 4

Бренд: PCE Health and Fitness Страницы: 7

Бренд: red lion Страницы: 4

Бренд: Deprag Страницы: 28

Бренд: TEA Страницы: 10

Бренд: janitza Страницы: 8

Бренд: Hanna Instruments Страницы: 2

Бренд: TSI Instruments Страницы: 78

Бренд: Triplett Страницы: 10

Бренд: IME Страницы: 14

Бренд: Hach Страницы: 414

Бренд: Teledyne Страницы: 105

Бренд: netAlly Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды