Hioki PW8001-01 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 262

background image

42

Setting Wiring Mode and Configuring Current Sensor Settings

Wiring mode

1P2W

(single-phase 2-wire)

Select this wiring mode when measuring a DC line.

The current sensor can be connected to either the source or ground terminal.

The wiring diagrams include examples of both.

See “Wiring diagrams” (p. 48).

1P3W

(single-phase 3-wire)

—

3P3W2M

(3-phase 3-wire)

Select this wiring mode when using the two-wattmeter method with two channels to

measure a three-phase delta configuration.

It enables accurate measurement of active power even when waveforms are

distorted due to an unbalanced state.

Apparent power, reactive power, and power factor values for unbalanced lines may

differ from corresponding values obtained from other measuring instruments. In

such a case, use 3V3A or 3P3W3M wiring mode.

3V3A

(3-phase 3-wire)

Select this wiring mode when using the two-wattmeter method with three channels

to measure a three-phase delta configuration, which is used when you emphasize

compatibility with legacy power meters such as the Hioki 3193.

It allows accurate measurement of not only active power, but also apparent and

reactive power and power factor even with unbalanced lines.

3P3W3M

(3-phase 3-wire)

Select this wiring mode when using the three-wattmeter method with three

channels to measure a three-phase delta configuration.

It allows accurate measurement even if the instrument in 3V3A wiring mode

yields an error due to leakage current with large high-frequency component when

measuring a PWM inverter, making it well suited to motor power measurement.

3P4W

(3-phase 4-wire)

Select this wiring mode when using the three-wattmeter method with three

channels to measure a three-phase Y (star) configuration.

Current sensor auto-recognition function

The instrument automatically acquires the rated current, phase correction values, and other
information of the current sensor connected to the instrument.
This function can significantly reduce the setting time before measurement, and measure the power
based on accurate sensor information.
(Only for current sensors supporting the auto-recognition function)

In the following cases, the instrument automatically acquires only the rated current of the current
sensor connected to the instrument.

•

When a current sensor not equipped with the auto-recognition function is connected to the

instrument

•

If the instrument fails to read current-sensor information, including phase correction values

List of optional current sensors

See “Optional products for current measurement” (p. 4).

HIOKI PW8001A961-00

«
...
46
47
48
49
50
...
»

Содержание PW8001-01







































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PW8001-01

Бренд: E+E Elektronik Страницы: 32

PowerCross-Laser 8 S

Бренд: LaserLiner Страницы: 64

ClimaHome-Check Plus

Бренд: LaserLiner Страницы: 10

MeterMaster Plus

Бренд: LaserLiner Страницы: 104

Бренд: LaserLiner Страницы: 52

LaserRange-Master T2

Бренд: LaserLiner Страницы: 52

Бренд: LaserLiner Страницы: 5

CombiRangeXtender 40

Бренд: LaserLiner Страницы: 84

SuperCross-Laser 2P

Бренд: LaserLine Страницы: 92

MoistureFinder Compact

Бренд: LaserLine Страницы: 56

LaserRange-Master Gi7 Pro

Бренд: LaserLiner Страницы: 56

Бренд: Laser Tools Страницы: 4

SmartVision-Laser

Бренд: LaserLiner Страницы: 56

Бренд: Oakton Страницы: 16

Бренд: R&S Страницы: 733

Бренд: R&S Страницы: 369

Бренд: RADWAG Страницы: 12

Бренд: Underground Magnetics Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды