hilscher 1912.112 Скачать руководство пользователя страница 55

Страница: 55 / 154

Configuration

55/154

Settings > Miscellaneous

Open the

Miscellaneous

sub tab.

Settings tab, Miscellaneous sub tab (example)

Parameter

Description

Value / Value range

Unique ID*

Unique ID of the IO-Link Device (9 Bytes)

Use the Unique ID (UUID) from the scan result.

0 … 0xFF, Default: 0

Slot type

Slot type of the found device

Use the slot type from the scan result.

Note: For a device featuring “Double slot” an even number must be
assigned as value for the slot.

Single slot, Double slot,
Default: Single slot

IMA Time 3 sec
(

calculated time

)

Requested I-Am-Alive time for the OPERATE mode

The I-Am-Alive time is calculated by multiplying the “time base”
with the “time multiplier”.

1.664 ... 10 min (for higher
values an error message
appears), Default: 3 sec

Time base: Used time base for the calculation of the I-Am-Alive
time.

1.664 ms, 5 ms, 1 sec, 1 min

Time multiplier: Used factor for the calculation of the I-Am-Alive
time.

1 … 255

Low power
device

Is the connected IO-Link Device a low power device or not

No, Yes, Default: No

Table 33: Settings in port configuration for IO-Link Device, Miscellaneous sub tab

* Values are in hexadecimal

To configure the Unique ID, use the Unique ID (UUID) from the scan
result.

If necessary, set the expected port parameters Slot type or Low power
device.

Configure the “IMA Time” (I-Am-Alive time).

Содержание 1912.112



























































































































































Результаты поиска

Содержание 1912.112

Отзывы:

Похожие инструкции для 1912.112

Бренды по названию

Популярные бренды

hilscher 1912.112, Руководство пользователя

Результаты поиска

Содержание 1912.112

Отзывы:

Похожие инструкции для 1912.112

Бренды по названию

Популярные бренды