HIKVISION DS-K3B601S Series Скачать руководство пользователя

Страница: 80 / 124

Note

You can check Display Failure Only to filter the applying results.

The selected persons in the applied access groups will have the authorization to enter/exit the

selected doors/door stations with their linked card(s) or fingerprints.

9. Optional: Click to edit the access group if necessary.

Note

If you change the persons' access information or other related information, you will view the

promptAccess Group to Be Applied on the right corner of the client.

You can click the prompt to apply the changed data to the device. You can select either Apply

Now or Apply Later.

Figure 7-8 Data Synchronization

7.7 Configure Advanced Functions

You can configure the advanced functions of access control to meet some special requirements in

different scene.

Note

• For the card related functions(the type of access control card), only the card(s) with access group

applied will be listed when adding cards.

• The advanced functions should be supported by the device.

• Hover the cursor on the Advanced Function, and then Click to customize the advanced

function(s) to be displayed.

7.7.1 Configure Device Parameters

After adding the access control device, you can configure the parameters of access control device,

access control points.

DS-K3B601SX Series Swing Barrier User Manual

Содержание DS-K3B601S Series





























































































































Результаты поиска

Содержание DS-K3B601S Series

Отзывы:

Похожие инструкции для DS-K3B601S Series

Бренды по названию

Популярные бренды

HIKVISION DS-K3B601S Series, Руководство пользователя

Результаты поиска

Содержание DS-K3B601S Series

Отзывы:

Похожие инструкции для DS-K3B601S Series

Бренды по названию

Популярные бренды