HIKVISION DS-7304HUI-K4 Скачать руководство пользователя страница 90

Страница: 90 / 220

DS-73xxHUI-K4, DS-73xxHQI-K4, DS-90xxHUI-K8 DVR User Manual

UM DS-73xxHUI-K4 DS-73xxHQI-K4 DS-90xxHUI-K8 092017NA

Figure 113,

Select Channels for Synchronous Playback

On the

Event Playback

interface, select the main stream or sub-stream

from the drop-down list for playback. The toolbar in the bottom part of
the

Playback

interface can be used to control the playing process.

Figure 114,

Interface of Playback by Event

10.

Pre-play and post-play can be configured for playback of event triggered
record files.

•

Pre-play

: The time to play back before the event. For example, if an

alarm triggered the recording at 10:00, if the pre-play time is five
seconds, the video starts playback from 9:59:55.

Содержание DS-7304HUI-K4





























































































































































































































Результаты поиска

Содержание DS-7304HUI-K4

Отзывы:

Бренды по названию

Популярные бренды

HIKVISION DS-7304HUI-K4, Руководство пользователя

Результаты поиска

Содержание DS-7304HUI-K4

Отзывы:

Бренды по названию

Популярные бренды