HIKVISION DS-7304HUI-K4 Скачать руководство пользователя страница 68

Страница: 68 / 220

DS-73xxHUI-K4, DS-73xxHQI-K4, DS-90xxHUI-K8 DVR User Manual

UM DS-73xxHUI-K4 DS-73xxHQI-K4 DS-90xxHUI-K8 092017NA

Figure 77,

Capture Settings

Select a camera from the drop-down list.

Configure the parameters.

Click

Apply

to save the settings.

(Optional) If the parameters can also be used for other cameras, click

Copy

to copy

the settings to other channels.

The interval is the time period between two capturing actions. You can configure all
the parameters on this menu upon demand.

5.2

Configuring Recording and Capture Schedule

The DVR supports continuous, alarm, motion, motion | alarm, motion & alarm, event,
and POS triggered recording types.

In this chapter, the record schedule procedure is used as an example, and the same
procedure can be applied to configure a recording schedule.

Purpose

Set the record schedule, then the camera will automatically start/stop recording according
to the configured schedule.

Go to Menu > Record/Capture > Schedule.

Содержание DS-7304HUI-K4





























































































































































































































Результаты поиска

Содержание DS-7304HUI-K4

Отзывы:

Бренды по названию

Популярные бренды

HIKVISION DS-7304HUI-K4, Руководство пользователя

Результаты поиска

Содержание DS-7304HUI-K4

Отзывы:

Бренды по названию

Популярные бренды