HIKVISION DS-7304HUI-K4 Скачать руководство пользователя страница 115

Страница: 115 / 220

DS-73xxHUI-K4, DS-73xxHQI-K4, DS-90xxHUI-K8 DVR User Manual

UM DS-73xxHUI-K4 DS-73xxHQI-K4 DS-90xxHUI-K8 092017NA

115

Select

Linkage Action

tab to set alarm response actions of video

tampering alarm.

Repeat the above steps to set arming schedule of other days of a week.
Use

Copy

to copy an arming schedule to other days.

10.

Click

to complete the video tampering settings of the channel.

11.

Repeat the

above

steps to finish settings of other channels, or click

Copy

to copy the above settings to them.

12.

Click

Apply

to save and activate the settings.

6.3

Setting All-Day Video Quality Diagnostics

Purpose

The device provides two ways to diagnose the video quality: manual and all-day. Perform
the following steps to set the threshold of the diagnosing and the linkage actions.

Go to Menu > Camera > Video Quality Diagnostics.

Figure 154,

Video Quality Diagnostics Interface

Select a

Camera

you want to detect video tampering.

Check the checkbox of Enable Video Quality Diagnostics.

To enable video quality diagnostics, the function must be supported by the selected
camera.

Содержание DS-7304HUI-K4





























































































































































































































Результаты поиска

Содержание DS-7304HUI-K4

Отзывы:

Бренды по названию

Популярные бренды

HIKVISION DS-7304HUI-K4, Руководство пользователя

Результаты поиска

Содержание DS-7304HUI-K4

Отзывы:

Бренды по названию

Популярные бренды