HIKOKI WF 18DSL, Инструкция по эксплуатации

Страница: 9 / 88

9
English
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease.
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specified by
the manufacturer.
A charger that is suitable for one type of battery
pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically
designated battery packs.
Use of any other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical
help.
Liquid ejected from the battery may cause irritation
or burns.
e) Do not use a battery pack or tool that is
damaged or modified.
Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion
or risk of injury.
f) Do not expose a battery pack or tool to fire or
excessive temperature.
Exposure to fire or temperature above 130 °C may
cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specified in the instructions.
Charging improperly or at temperatures outside
the specified range may damage the battery and
increase the risk of fire.
6) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
b) Never service damaged battery packs.
Service of battery packs should only be performed
by the manufacturer or authorized service providers.
PRECAUTION
Keep children and infirm persons away.
When not in use, tools should be stored out of reach
of children and infirm persons.
CORDLESS AUTOMATIC SCREWDRIVER
SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting a "live"
wire may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
ADDITIONAL SAFETY WARNINGS
1. Always charge the battery at a temperature of 0 – 40°C.
A temperature of less than 0°C will result in over
charging which is dangerous. The battery cannot be
charged at a temperature higher than 40°C.
The most suitable temperature for charging is that of
20 – 25°C.
2. Do not use the charger continuously.
When one charging is completed, leave the charger for
about 15 minutes before the next charging of battery.
3. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
4. Never disassemble the rechargeable battery and
charger.
5. Never short-circuit the rechargeable battery. Short-
circuiting the battery will cause a great electric current
and overheat. It results in burn or damage to the battery.
6. Do not dispose of the battery in fire.
If the battery is burnt, it may explode.
7. Bring the battery to the shop from which it was
purchased as soon as the post-charging battery life
becomes too short for practical use. Do not dispose of
the exhausted battery.
8. Using an exhausted battery will damage the charger.
9. Do not insert object into the air ventilation slots of the
charger.
Inserting metal objects or inflammables into the charger
air ventilation slots will result in electrical shock hazard
or damaged charger.
10. When mounting a bit into the keyless chuck, tighten the
sleeve adequately. If the sleeve is not tight, the bit may
slip or fall out, causing injury.
11. This automatic screwdriver is designed for tightening
and loosening screws. Use it only for these operation.
12. One-hand operation is extremely dangerous; hold the
unit firmly with both hands when operating.
13. Use original bits specifically for the automatic
screwdriver.
Use no bits other than the original bits specifically for the
automatic screwdriver. Use of any other bit can result in
screws sticking out and screw feed malfunctioning.
14. After installing the driver bit, pull lightly out the bit to
make sure that it does not come loose. If the bit is not
installed properly, it can come loose during use, which
can be dangerous.
15. Screw in screws with the main unit held straight.
If the driver is slanted relative to the screw, the screw
head can be damaged and the bit worn. Moreover,
the prescribed torque is not transmitted to the screw,
resulting in screws left sticking out. Place the drive
straight against the screw and screw in.
16. Use the prescribed screws.
Do not use any other screws. They can cause abnormal
work (screws fallen over or sticking out) and break
downs (screw jamming and bit wear).
17. Protect your eyes with protective glasses.
Always wear protective glasses while working. Drilling
scatters plaster powder and tape dust, which are
dangerous if they get into your eyes
18. Watch out for wires and pipes in walls and ceilings.
When working on floors, walls, or ceilings, check for
wires and pipes ahead of time. Work carefully to avoid
shocks and explosions.
19. When the screw feed attachment is removed, always
use the correct driver bit for the screw size.
0000Book_WF18DSL_WE.indb 9 2019/03/11 14:23:11