HIKOKI CS 3630DB, Инструкция по эксплуатации

Страница: 17 / 300

17
English
10. Cleaning of the outside
When the chain saw is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use chloric
solvents, gasoline or paint thinner, for they melt plastics.
11. Storage
○ Clean all parts thoroughly. Coat metal parts with a thin
layer of corrosion inhibitor.
○ Be sure to repair any damaged areas before storing.
○ When storing the unit, perform cleaning and
maintenance of each part and mount the chain case to
the guide bar.
○ Store the chain saw in a place where the temperature is
less than 40°C and out of reach of children.
NOTE
Storing Lithium-ion Batteries
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
signi fi cantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, signi fi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to fi ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries
dead and purchase new batteries.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
Important notice on the batteries for the HiKOKI
cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used
with batteries other than these designated by us, or
when the battery is disassembled and modi fi ed (such
as disassembly and replacement of cells or other
internal parts).
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with
statutory/country speci fi c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling instruction,
to a HiKOKI Authorized Service Center.
Information concerning airborne noise and vibration
The measured values were determined according to
EN62841 and declared in accordance with ISO 4871.
CS3630DB
Measured A-weighted sound power level: 107 dB (A)
Measured A-weighted sound pressure level: 87 dB (A)
Uncertainty K: 3 dB (A)
CS3635DB
Measured A-weighted sound power level: 105 dB (A)
Measured A-weighted sound pressure level: 85 dB (A)
Uncertainty K: 3 dB (A)
Wear hearing protection.
Vibration total values (triax vector sum) determined
according to EN62841.
CS3630DB
a
h = 2.5 m/s 2
Uncertainty K = 1.5 m/s
2
CS3635DB
a
h = 2.4 m/s 2
Uncertainty K = 1.5 m/s
2
The declared vibration total value and the declared noise
emission value have been measured in accordance with a
standard test method and may be used for comparing one
tool with another.
They may also be used in a preliminary assessment of
exposure.
WARNING
○ The vibration and noise emission during actual use
of the power tool can di ff er from the declared total
value depending on the ways in which the tool is used
especially what kind of workpiece is processed; and
○ Identify safety measures to protect the operator that
are based on an estimation of exposure in the actual
conditions of use (taking account of all parts of the
operating cycle such as the times when the tool is
switched o ff and when it is running idle in addition to
the trigger time).
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci fi cations herein are subject to
change without prior notice.
000Book̲CS3630DB.indb 17 000Book̲CS3630DB.indb 17 2021/01/15 12:33:01 2021/01/15 12:33:01