Hettich EBA 280 Скачать руководство пользователя страница 33

Страница: 33 / 45

AB1101EN_SA

Rev. 01 / 11.2022

33/45

20.9

Resetting the cycle counter to zero

After the rotor/hanger has been exchanged, the cycle counter of the respective rotor code must be reset to zero
again.

The cycle counter may only be reset to zero if the rotor/hanger has been exchanged for a new rotor/hanger
first.

With the rotor at a standstill, the cycle counter can be reset as follows:

The procedure can be aborted at any time by pressing the

STOP

OPEN

key. In this case, the settings are not stored.



Press and hold the button for eight
seconds.

PROG

t/min:s

RPM





Press the key until the following is
displayed:

PROG

t/min:s

RPM



START

PULSE



Press the key.

Example:

PROG

t/min:s

RPM





Press the key until the following is
displayed:

Cyc sum :

Number of completed run

cycles.

PROG

t/min:s

RPM



RCF



Press the key.

PROG

t/min:s

RPM





Press the key.
The number of completed run cycles is
reset to zero.

PROG

t/min:s

RPM



START

PULSE



Press the key to save the setting.

PROG

t/min:s

RPM

PROG

t/min:s

RPM



STOP

OPEN



Press the key twice to exit the "

Time &

Cycles" menu or press three times to exit
the " MACHINE MENU ".

PROG

t/min:s

RPM

Example:

PROG

t/min:s

RPM

Содержание EBA 280














































Результаты поиска

Содержание EBA 280

Отзывы:

Похожие инструкции для EBA 280

Бренды по названию

Популярные бренды

Hettich EBA 280, Руководство по эксплуатации

Результаты поиска

Содержание EBA 280

Отзывы:

Похожие инструкции для EBA 280

Бренды по названию

Популярные бренды